Having problems with your Electrolux Vacuums ?

How do i get into the electrolux discovery II powerbrush assembly? I have removed all screws but still no access?


Answers :

There are two square holes on the outer side of the wheels. Use a flathead screwdriver in these to release the latches. Turn the powerhead over and carefully lift the back of the cover off and pull back slightly to lift off. To remove the brush and/or replace the belt, remove the tiny screw on each end of the brush and lift brush out.
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i get into the electrolux discovery II powerbrush assembly? I have removed all screws but still no access?


There are two square holes on the outer side of the wheels. Use a flathead screwdriver in these to release the latches. Turn the powerhead over and carefully lift the back of the cover off and pull back slightly to lift off. To remove the brush an ... Electrolux Vacuums

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

BURNING SMELL My DC 07 has suffered from poor suction in the upright position for some time now but this morning it ground to a halt. It was if the motor had burned out. I turned it upside down and some small stones etc tumbled out. I tried switching on again and the motor kicked in but the smell was horrendous so i switched off immediately. If it's likely to be **** inside the motor area i don't no how to access it. I've removed for fixing screws but still unable to prise apart. Is it just the


Hi.\015\012\015\012Try this site http://dysonmanuals.llc.nu/ has service manuals covering removing the Dc07 motor. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

How do I replace the motor brushes in my DC11? I cannot dismantle beyond removing the pipe attachment. I've removed the 6 fixing screws that are visible, but the machine is still firmly "together" as if there are still screws that I've not located. Does it snap apart? Are there hidden screws? Paul


You can buy brushes but if the armature is overheating changing the brushes wont help ... Dyson Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o


Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.


Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Base Plate screw rotating in insert and not coming out. Insert come unfixed with screw still attached. Therefore unable to remove baseplate, unable to remove cotton fibres from brushes. Have you an engineer in the vacinity of york(NOT A SALESMAN WITH A FRANCHISE) PLEASE


Try to remove all other base plate screws first. If they can be removed gently try to pull open by hand against the lid while rotating the remaining screw. You will need to apply outward pressure betweent the insert and baseplate to remove it while r ... Vacuums

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?


... Vacuums

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

How do i remove the reel cover for my SEARS canister model 116312690 vacuum cleaner. we are unable to move the cord forward or back. We have found two screws, but are still unable to remove the cove


... Kenmore Vacuums

Hi. We've got a Dyson DC17 "Animal". It's clogged, and we are unable to separate the purple cyclone cap from the main cyclone body to get to the problem. We've heard of 4 torx screws that take some interesting tactics to access. I've been through this thing with a flashlight, and torx tools for a protracted period, and even after removing the torx screws was unable to ultimately separate the two pieces (main body from purple cap assembly). Any help would be greatly appreciated. Thanx -


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a EuroPro Infinity NV29 and I have a clog in the base. I have removed the screws and the plastic piece where it says access port to remove clogs but don't know how to get the hose lose to empty it.


... Vacuums

I have a Kenmore Wispertone 300 cannister and I am trying to access the motor. There are four screws shown in the parts diagram. I need to remove the plastic on/off pedal to acess two screws. How do I release the pedal?


I just encountered the same problem on a Whispertone 116 last evening. If it is the construction same as mine, there are four flexible plastic retainers molded into the top cover in the gap between the pedal and the motor cover. These are on the hing ... Kenmore 23313 Whispertone Bagged Canister Vacuum

How do you dismantle a Panasonic MC-3920 vacuum cleaner? I have removed the 4 screws at the top but still doesn't come apart and one got ideas. How do you remove the blue top cover ?


... Panasonic MC-3900 Bagged Canister Vacuum

HOW DO YOU REMOVE THE TOOTHED DRIVE WHEEL FROM THE BRUSH MOTOR ON MY BISSELL 9200E CARPET CLEANER. ALSO IS THE ATTACHED UNIT THE MICRO SWITCH? WHY IS THE MOTOR COVER STILL ATTACHED TO THE FRAME WHEN ALL 4 OFF SCREWS ARE REMOVED JIM


It is a snap lock plastic cap on mounted to the frame. ... Bissell 9200 Upright Vacuum

How do you replace a belt on the a Simplicity Synergy vaccuum? Removing the 2 screws on the bottom plate allows you to access the roller, but doesn't give you access to the drive motor. Any ideas?


... Simplicity 7850 Premier Bagged Canister Vacuum

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??


... Eureka Capture Upright Vacuum Vacuum

Dyson dc04 I have just stripped machine and found the drive belt from the motor snapped. How do I remove the clutch assembly from the housing? I have removed the 2 screws but the yellow knobs are still in place.


Hi,\015\012\015\012Go to this site for manuals to help with your Dc14.\015\012http://dysonmanuals.llc.nu/\015\012\015\012Chris. ... Vacuums

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

I have a bosch ergomaxx 2000w which I need to strip down and clean. Ive found 6 torx screws bit still can't remove the coloured plastic cover. How do I remove it?


Got the same !Remove both back wheels (just pull gently with a screwdriver), then with a big screwdriver pull the cover while pulling plastic locks in the side holes (under the wheels) whith a small screwdriver. ... Bosch Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0417 seconds