Having problems with your Electrolux Vacuums ?

My electrolux brush roller is not working, how do I fix it?


Answers :

Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller does not work. My vacume works fine , but the roller does not work. How can i fix that/


Remove the brush assembly, and clean/oil (3in1 or similar) the end bearings. If the belt is broken/damaged, replace same. Install the belt on the roller and motor shaft, then install the brush into the vacuum base--make sure the belt is half twisted ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

The suction on my eureka optima stopped working but the roller still works, what might i do to fix it?


Hi there. Most suction problems are due to a blockage. Start with the base and look carefully for debris that is stopping air flow. You may have to remove the base plate to get to the problem. I am including a link to the manual for your machine. ... Eureka 431A Optima Bagless Upright Vacuum

Electrolux Upright Versatility vacumm cleaner- When I use the CARPET power button, the roller does not work. Red wording lights up that says 'Check Rollerbrush'. How do I reset or fix the rollerbrush? thanks! I have guests coming and I really need to vacumm!


... Electrolux 1910 Bagless Upright Vacuum

The roller in the powerhead has stopped spinning, therefore it is not picking up anything. I took the powerhead off and everything else is working great including suction. What is the best way to fix this problem? Thanks, Carolyn


... Hoover S3825 Bagless Canister Cyclonic Vacuum

Boss smartvac The piece that keeps the roller from moving when set on hose doesn't work right. I keep breaking belts. How do I fix this?


... Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

I have a bissell healthy home vacuum and the roller bar on the base of it is not working. I have checked it for obstructions and it is clear. I have also tried reseating the canister and just about everything I can think of. It's almost like the switch that deterrmines whether or not the vacuum is in the upright position is broken and always says it is upright... any way to fix that? Thanks, Scott Hammersley


... Bissell Vacuums

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis


Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The model is U5720950, there is no suction at all when I lower the handle to vacuum. But when I use the parts, they work properly. I cleared the roller and put everything back in place. Did I misplace something? Can I fix it myself without taking it to service?


... Hoover U5720-900 WindTunnel Upright Vacuum

My electrolux brush roller is not working, how do I fix it?


... Electrolux Vacuums

My daughter accidentally got a scarf partially stuck in our Eureka Boss, now the roller won't work. Is there anything I can do to fix it?


Hi,There are a couple of tabs on both sides of the top housing that need to\015\012 be unlocked by using a flat screw driver, then the top will come off. \015\012The u shaped collar on the tube will then give way to take the roller \015\ ... Eureka Smartvac 4870 Bagged Upright Vacuum

The roller brush stop working


The fuse in the plug may have blow so replace it any ways ... Dyson Ball DC24 Bagless Upright Vacuum

After fixing rollers not turning the water will not dispense out


Ensure you have water in tank and solution (or water in solution tank). When you start the vacuum up, the pump starts to prime itself. If you have air in the system, it takes a little longer to prime. Allow the vacuum to run for 1 minute before attem ... Bissell 9200 Upright Vacuum

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen


Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

My Riccar 8850 belt works but the roller will not spin


I see this same problem posted repeatedly here. The only solutions offered are to "change the belt". When most people state that they've changed the belt and still have the same problem the recommendation is usually "are you sure you changed the be ... Riccar 8850 Vacuum

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.


... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

My electrolux Epic 6500 power nozzle Model N109J will not work. It had an intermittent short which I thought I fixed (some of the insulation on the wires were pinched). I fixed the wires and it worked intermittently for an hour then shut down completely. Could the reset switch have a short? When I press the switch nothing happens.


The switch is definitely a possibility, but other problems can also cause this.\015\012Bad switch, needs replaced.\015\012Broken wiring in power nozzle, wands, hose, or canister.\015\012Bad PN motor.\015\012\015\012I str ... Electrolux Epic 6500 Vacuum

How do we fix roller brush on dyson dc14 full gear?


Have you also checked that the brush control knob is set to "carpet"? The brush will not spin in "bare floor" mode. (Sorry if this seems too obvious to mention, but I see lots of Dysons where incorrect setting of that knob is the only problem.) Fail ... Dyson DC14 Full Gear Bagless Upright Cyclonic Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

When I turn the vaccuum on the roller works for about 20 seconds, then I hear an awful, loud noise, and the roller does not work. Sounds like maybe some gears are being stripped? Please help


It sounds like you need to change the belts. You can get replacements and view the manual here:Dyson DC07 Belts and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.


Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

Nothing inn the canister after using,suctione working,bottom roller working,no air leaks from hoses.Also when running awhile it shuts off by itself,have to wait awhile to use again


I'm not sure what vacuum you have, but that sounds like a blockage to me. Thermal shut off kicks in, shutting the motor down, to prevent damage from overheating. After waiting like 1 hour it probably comes back on. Make sure hose, filters, bag (if an ... Vacuums

The roller on my power head does not spin consistently. So my vac is not picking up of course. The square end pieces and the rod that goes into the wooden roller seem loose. I tried tightening it but it still is not turning. Can I do a fix with glue or something till I can get a new roller?


... Rainbow E series Canister Wet/Dry Vacuum

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0592 seconds