Having problems with your Electrolux Vacuums ?

How to remove cord reel

\015 Electrolux 2100 removal of cord reel\015

Answers :

Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)


You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum

How to remove cord reel


... Electrolux Vacuums

How do i remove the reel cover for my SEARS canister model 116312690 vacuum cleaner. we are unable to move the cord forward or back. We have found two screws, but are still unable to remove the cove


... Kenmore Vacuums

How to remove hoover wind tunnel cord reel?


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Pwr cord rewind reel


You have to pop the grey button off for the cord rewind. There is one more screw under there. You have to be very careful, because you can break one of the tabs that hold the button on. In fact, it is almost a garuntee. There are three tabs that stic ... Hoover S1361 Bagged Canister Vacuum

KENMORE 116.25915503 CORD REEL


... Kenmore Vacuums

Miele Red Star model S314. Cord reel is stuck. About three feet of cord is out. The rest of cord is jammed inside machine? How do I get to where the cord reel is?


It is actually simple when I tell you, Here we go... \012\012First, open the lid and take the bag, and hepa filter out of the machine. \012\012With a slot screwdriver, pry the hinges of the bag door out a little and take the b ... Miele Red Star Bagged Canister Vacuum

I need to replace electrical cord on hoover windtunnel UH70120. How do i get the cord reel off? Can i open the cord reel to replace the cord?


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.


When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum

I'm replacing part # 8175156 cord reel on my Kenmore canister vacuum. How do I tension the spring? Do I do that before winding the cord onto the reel?


... Vacuums

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel


What is the exact model # please?Thanks!! ... Kenmore Vacuums

Replace Cord on Filter Queen with Cord Reel


... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

I was blowing snow with my Toro Power Curve 1800. I was distracted for a moment and tangled the cord in the blade. The cord is wraped around tight, how can I remove the cord?


Unless you are able to turn the blade backward and pull on the cord at the same time no luck. it may be easier to just cut the cord and install a new one. solution one is best and both require taking the machine apart. start there and hope it works o ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Power cord Cord is just all knotted a twisted, i bought a rubber cord and just want to replace the original. I have removed all the screws from the rear of the machine and it still doesn't want to come apart and i dont want to force it. any help is appreciated.


If the cord goes in at the top, take the handle off, then remove the tool holder, then you can get to the cord. If it goes in at the bottom, You have to take off the motor cover to get to the connecting end. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have an aerus electrolux guardian canister vacuum. The cord was damaged but the retraction winder is still fine. I have ordered a replacement cord but I have no idea how to remove the old cord and install the new one. Am I over my head?


The winder is activated by a coil spring located in a drum. The drum transmits the power from the wire with 2 circular contacts. To replace the cable you must dismantle the case to access the drum, take the spring pressure out carefully as to not let ... Vacuums

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930


... Hoover Vacuums

Electrolux Oxygen Classic cord winder/cord reel disassembly?


... Electrolux Vacuums

Power cord broken inside reel


The reel doesn't come apart, its a replaceable item. the only place that you can get another one is through sears. ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I'm trying to replace the power cord on my Hoover Telios vacuum cleaner. I have the machine open on the floor, but can't work out how to find the terminals on the cord rewind reel - they seem


... Hoover Telios Canister Vac Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0356 seconds