Having problems with your Electrolux Vacuums ?

Z61 brush won't rotate belt ok - Electrolux Vacuums


Answers :

Hartlepoolke:

Unplug the vacuum, turn it upside down and remove the floor plate so you can access the beater bar. Remove the belt from the motor shaft and remove the beater bar and belt from the machine. At each end of the beater bar there will be a small circular bearing. Carefully remove the bearings from the ends of the beater bar, and remove the collection of hair, carpet fibers and any other junk wrapped around the bearing mount studs. Grab an old pan... (something to wash the bearings in) and an old toothbrush. Scrub the bearings with the toothbrush dipped in rubbing alcohol, and attempt to spin the bearings by hand as you clean them. When the bearings will spin freely, dry them out, and put a drop of oil (preferably 3-in-1 or light machine oil in the bearing. Don't soak the bearing in oil, that will just attract more junk to jam the bearing. Wipe the bearings off and rotate them to ensure that they aren't ratcheting or siezing up. Check the belt to ensure that the motor spindle has not damaged the inside surface of the belt... If it has, a new belt may be in order. Reassemble the vacuum and you problem should be solved.
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Z61 brush won't rotate belt ok - Electrolux Vacuums


Hartlepoolke: Unplug the vacuum, turn it upside down and remove the floor plate so you can access the beater bar. Remove the belt from the motor shaft and remove the beater bar and belt from the machine. At each end of the beater bar there ... Electrolux Vacuums

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

The brushes on my new healthy home vacuum wont rotate when the machine is turned on how do i access the belt location


If you turn the vacuum over so you can see the brush roll, there is a brush cover that is held on by (4) screws. Remove those screws and the base plate cover will come off. With the base plate cover off you can access the roller brush an belt. If you ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.


You need to replace the belt. Replacement Vacuum Belts ... Vacuums

Roller Brush on Electrolux Nimble vacuum not rotating.


... Electrolux 5740 Upright Vacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an Electrolux El8502 Upright Vacuum and the brush roller does not rotate. I took off the roller and the pulley and started the vacuum. I notice that the cam is not rotating. Any suggestions much appreciated.


Hi, you can use thelink below to do a troublshooting tips for your upright vacuum..http://home.howstuffworks.com/how-t ... Electrolux EL8502 Versatility Bagless Upright Vacuum

Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.


It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?


This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

Most Vacuums has the belt in the middle of the rotating brush. This one has it on the left side and doesn't go around the brush. Mindboggling !


The belt runs from the metal motor pulley straight to the brush roll. To change the belt you remove the bottom plate, pull the roller straight up, then you put the belt on the metal pulley and then on the roller and you push it back into place. ... Sharp Twin Energy EC-TU4606 Bagged Upright Vacuum

KENMORE 27614 CANNISTER VACUUM The roller vacuum brush does not rotate. I check the belt and it is fine. Waht could be the problem?


... Kenmore Vacuums

My dc17 squeals when the brushes are rotating. I have replaced the brushes twice and the belt three times. It has been back to the factory twice and they say they have done the same thing. The suction is still there but it is getting to the point I might have to wear ear plugs to vacuum any suggestions.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Bissell 3920. The brush will not rotate when it is on carpet but it does rotate at a fast pace when the vacuum is tilted back. The belt is fine, not worn or torn.


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

Brush won't rotate. New vacuum. Any ideas. - Electrolux EL5010A Bagged Upright Vacuum


Has all packaging material been removed? Is the belt in place on the bottom of the vacuum? If these are done, I would return it immediately for a replacement.\015\012\015\012\015\012Thank You for using Fix Ya. Your rating is always ... Electrolux EL5010A Bagged Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

The scrub brushes wont rotate - Hoover Steam Vac Dual V w/ SpinScrub Vacuum


Clean it should be hair struck ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Eureka the boss upright bagless vacuum. how do i open it to get to the belt area? the brush seems stuck. it wont move


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=801547\015\012Generic problem for all Vacuums\015\012Eureka the boss upright bagless\015\012 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1398 seconds