Having problems with your Electrolux Vacuums ?

Electrolux el8501 roller not turning

\015 Motor runs, but pulley that turns the belt is not turning.\015

Answers :

Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux el8501 roller not turning

... Electrolux Vacuums

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen

Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

I have electrolux 4000 upright,when turned on roller works but theres no suction

Maybe your hoses are plugged with something. would happen to mine and i would find all kind of stuff in there. give that a try ... Electrolux EL8502 Versatility Bagless Upright Vacuum

I have the Electrolux Intensity upright vacuum. The roller bar underneath that is used for carpet no longer turns. I have checked the belt that is attached to it. I'm afraid that it may be the motor. Where can I take it for service or shat do I do now? Kay

... Electrolux Vacuums

My Electrolux Upright vacuum cleaner will not suction. Motor will run to turn roller, though.

The air passage form the brush area to the bag is plugged somewhere. Remove the lower plate and the bag above so that you have access to the air passage from both ends. A hooked, stiff wire will help pull the debris out. This problem is usually cause ... Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

The brush roll does not turn or turns very slowly in my Electrolux model EL6986 A

... Electrolux UltraSilencer Vacuum Cleaner (formerly the Harmony) Fast Free S

Uprightvac 3500SA roller is not turning

When you lower the handle on the electrolux, you will see a little button on the top of the base . This is a reset button, turn the vaccum on and push the resrt button and it should start working again. ... Electrolux Epic 3500 Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


Riccar model rad.7 upright (radiance). roller brush won't turn and red roller brush indicator is on. roller will turn easily by hand and belt is in place. how do i fix this?

As you already know, the red brush indicator light indicates that the brush roll has stopped turning, usually because an object has become stuck in the brush roll. When that happens you should turn the machine off (unplug it also for safety), remove ... Riccar 8955 Upright Vacuum

Kemore Progressive Vacuum 116.35923500. Where is the switch that turns on the agitator roller. It will only turn on if the handle is laying flat. When I lift it up slightly the roller turns off. Bill

... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

A cap on one end of the roller brush is centered and turns freely. The one on the other end is not centered and does not turn but does not look broken. It looks like it's supposed to be that way but it doesn't allow the roller brush to turn. How to I solve this?

It's hard to say definitively what the problem is here. Rollers usually have bearings at each end and they can wear or freeze up especially if they are exposed to water. When you say that the cap is not centered, I assume that you mean that you hav ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!

The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

Roller I recently removed my roller to cut all the hair off it and when I replaced it everything snapped right in but when I turned the power on the power worked but the roller wouldn't turn

Hi.\015\012\015\012Did you put the drive belt back on the roller ? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Roller does not turn; I was vacuuming a rug and a string got stuck in roller-took it off but now the roller will not turn. suction is fine.

The roller drive belt may be stripped, worn partway through where it goes around the motor shaft, thrown off the motor shaft, or broken. Take the bottom plate off the carpet sweeper and have a look.If the belt was damaged when the roller ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dyson DC14 roller doesn't turn but everything else works. The belt is on correctly, the roller is clean and it turns manually so I can't figure out the problem.

The DC14 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" and "carpet". The roller will turn only when the knob is on "carpet", and even then only when the handle is tilted back ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush roller will not turn. checked the belts, checked the brush roller gears and they are good too... the motor is not turning .. could it be a switch somewhere?

... Electrolux EL5020 Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

Brush roller won.t turn. It turns for a sec. then shuts off. I have cleaned all clogs. This is a shark navigator. Can I remove bottom of vac to access the roller? The manual doesn,t mention this as a solution.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

I unscrewed the roller brush protective cover and removed the brush to clean it. Now the roller won't turn because the drive shaft is not turning. Is there a reset button or something?

I looked at the pictorial of this vacuum at this URL:\015\012http://middleeasten.bissell.com/images/UserGuides/3750.pdf\015\012\015\012This shows the belt to slide on the motor drive pulley and also on the brush. If the brush is bound up on th ... Bissell 3750 Lift Off Bagless Upright Vacuum

The roller will not turn off on our Oreck Halo. As soon as I plug it in, the roller turns on. Any ideas?

Not familiar with the Oreck Halo, but that sounds like a shorted switch. ... Oreck Vacuums

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and

Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Dirt Devil Vibe bagless vacuum started giving off a burning smell. The brush roller was jammed with hair. I immediately shut it off and cut the hair out of the rollers with scissors until it turned freely. When I turned it back on, the smell was gone but there's no suction now. Did I ruin the belt or something else?

It's more likely there's a clog in the hose somewhere, possibly where it connects to the power nozzle. Detach hose and check the PN. \015\012If there's no clog in the PN, detach hose completely from machine and try to drop a marble or coin th ... Windsor SR12 Sensor Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0463 seconds