Having problems with your Electrolux Vacuums ?

I have a electrolux el6989 that the power head keeps quitting for a second then comes back on. Acts like it has a short starting

Answers :

Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a electrolux el6989 that the power head keeps quitting for a second then comes back on. Acts like it has a short starting

... Electrolux Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio

Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

My dyson hand held shuts down after about 30 seconds, It turns back on again, but it does this over and over again, even after being fully charged with caontainer emptied. Its almost like an overheating thing, but different since it starts right back. It is annoying.

... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary

This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth

Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

Could I have a short in my cord? I can vacuum & then when I move the canister it shuts off, if I wiggle the cord it will turn back on. This last time, it just revs like a car trying to start & then does nothing. I live in a VERY remote area (80 miles from nearest Wal-Mart or McDonalds) so I know I will not be able to find someone to repair this for me. I have great doubt that I will be able to do it myself & my husband is an accountant so he is unavailable for another 6 weeks!!!!! Any suggestion

Whit the vacume plugged in and turned on start where the cord goes in to it and hold the cord whith each hand and bend it slightly. Move up the cord and do the same if there is a brake in the cord the machine will loose power until you bend the secti ... Miele Red Star Bagged Canister Vacuum

At first when I tried starting my B & S I primed the motor and it ran for a few seconds and died. This happened twice. I drained the tank and took apart the cvarb and blew out the entire carb. Put it back together changed the plug and now nothing. Could it be that the priming diaphriam (#694395) has a hole and thus preventing gas to come up from the carb bowl?

Hi tifix1...\012Yes, that could cause your problem.\012I will offer a few more things to check and repair/replace, maybe there is a few things that you missed.\012Please take time to rate me\012\012Sounds like you have d ... Vacuums

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My shark steamer has stopped working after a year of having it (I have already replaced one, I'm a idiot!). My problem; however, is that it will steam, but the steam stops traveling through the actual "mop" part. I plugged it in, wait seconds and start pumping, but the steam builds up until it's hard to pump. I had to press the button really hard for the bottom to come off and it shot off like a rocket! I tried to stick something through the tubing, but it did nothing. What am I doing wrong? I

\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Motor grind Loud sound and smell on occasion. Started as just short sound as turned off, +/- 2 seconds. Now does it on star up unless I tilt the unit back. Ideas? Is it worth fixing? ns

Try checking the belt, that is probably the smell, might need replacing ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little

Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.

It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.

... Broan-NuTone VX475 Bagged Central System Vacuum

My new H2O Mop Ultra (Danoz) seems to heat up ok then when the light switches to green and I start using it, the orange light comes back on as well as the green. Produces steam to start with but then it starts to spit water too and everything ends up wet. Any ideas on whats wrong or should I just send it back?

That is a major hardware fault, I have seen this numerous times with these H2O mop's... They seem to either work perfectly for a long while or have problems right off the bat. You definitely want to send this unit back and either get a refund or at ... Vacuums

The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.

This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums

Nilfisk GD-2000. Same problem with the new vacuum as the old one, runs 30 seconds to a minute & shuts down. Sometimes it'll start & run another 30 seconds or so, but shuts down. Other times it won't start back up at all. No clogs & bag is new. Please help.

... Vacuums

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a vx550cc that keeps kicking in and out quickly, then shuts down for a few seconds and starts up kicking in and out again. There is lots of suction at all the outlets and sweeps. The dirt bucket has been emptied and the filter cleaned. Al the LED lights light up when the motor kicks out, then back to one green when it starts back up. This unit has worked great for four years with no problems.

... Broan-NuTone VX475 Bagged Central System Vacuum

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.

Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

Lately we've been having plumbing problems to where our washing machine floods up our bath tub and toilet. And it happens while we have the washing machine on of course. Another problem is that whenever we are taking a shower our tub starts to clog up and water starts pouring out from the bottom of our toilet. We had a plumber come by to root out our pipes just last week and it was fine for about 3 days. And now the problem is back and driving me crazy. WHAT IS WRONG AND HOW CAN I FIX IT??

Possible tree roots best thing is to hire a plumber with a camera snake ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

I have a bissel proheat carpet cleaner. THe trigger is stuck in the on position. However, no water or shampoo is coming out. I can pry it back out but it feels like a spring is missing or something like that.

You may need to replace the handle assembly, or at least take it apart and reconnect the spring inside the handle..here is the repair manual, which has good illustrations on page 9 and 22 of working on the handle..http://newz ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0965 seconds