Having problems with your Electrolux Vacuums ?

I have a 1521 Diamond Jubilee Vaccum cleaner. The last time I used it the motor seemed to slow down and then pick up to normal speed. When I turned it off and then back on, it did not start.

Answers :

Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1521 Diamond Jubilee Vaccum cleaner. The last time I used it the motor seemed to slow down and then pick up to normal speed. When I turned it off and then back on, it did not start.

... Electrolux Vacuums

Sharp R-1480. Microwave would not start - jarred door, and it heated and worked. Replaced bottom of the 3 inter-lock door switches. Turns back on - all seems normal. No heat (it does overall sound louder). Thanks, Mark [email protected]

Hi Mark,It sounds like you have a magnetron problem now or at very least a rectifier that is shorted. The elevated sound level comes from one of those two components. But since you had a door switch problem I would lean toward ... Vacuums

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio

Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

Kenmore Quick clean MICRON 12 amp vacuum cleaner worked. I turned it off and was going to turn it back on and now it will not turn back on. Do they have a re-start button and if so where would I find it?

... Kenmore Quick Clean 30012 Vacuum

I bout this vacume in mid December 07 and about February-March it started not picking up the dust on the floor. So in early April I bout a new filter and it still wasn't picking up the way it had in the beginning. I've taken it a part several times and cleaned it out with it being plugged at the bottom hose with dust bunnies. Well I just took it back to Walmart where I purchased it and I failed to keep the reciet they could not do any thing about the sweeper. I went back to the sweepers and re

Pull the hose out of the holder, is there suction there. If not, then there is a clog in the hose. If there is suction, then check the dirt outlet by the brush roll. Also if the belt is slipping, it may appear to not have as much suction, belts wi ... Dirt Devil Vacuums

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and

Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition

Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo

It sounds as if you have a clog inside the "Power Nozzel". They mention that there are "no user serviceable parts within the Majestic® Power Nozzle" My advice would be to see if you can see a clog with in reachable distance and try to remove the ... Filter Queen Vacuums

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

During the winter i turn the dehumidifier off. but when i turned it back onthis spring because you can feel the dampness in basement, it turns on but it does not absorb any water. i cleaned filter??? it turns on and sounds normal but it isn't taking any water in??? help

Turn the machine on maximum and let it run for an hour or so. Then check the coils in the back with your hand. If they are not getting cold at all, then there is a significant problem with the refrigeration process in the unit. It may have developed ... Vacuums

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther

... Clarke Vacuums

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.

There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t

... Vacuums

My model 4870 Eureka type K Vacuum Cleaner won't turn back on after it started smoking. I turned it off, checked the belt and filters, and they seemed to be fine. The brush will turn so I don't think the motor is seized up. where do I go from here? Thanks for you help, David Andrews

... Eureka Smartvac 4870 Bagged Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!

Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o

... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.

I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.

... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

As you turn the Sebo on, the 2 red lights flash once and there is no motor. If you rotate the brush roller the motor starts. We've taken off the brush roller and put it back on and now it doesn't even start when you rotate the roller.

... Sebo Automatic X1 Bagged Upright Vacuum

Roomba is not picking up dirt but does pick up dust. That is, the dust chamber has dust in it but the dirt chamber is empty. The brushes don't have any fluff on them either which is not normal. The fan is blowing out plenty of air, the filter has been cleaned but we suspect the brushes aren't turning. an you help?

... Roomba Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0872 seconds