Having problems with your Electrolux Vacuums ?

Renaissance manual how do you get the swivel head off to get to the wiring for the wand


Answers :

Disconnect the power from the unit, then remove two screw in the handle and pull the handle apart and this will expose the wires.
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Renaissance manual how do you get the swivel head off to get to the wiring for the wand


Disconnect the power from the unit, then remove two screw in the handle and pull the handle apart and this will expose the wires. ... Electrolux Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?


Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

I have an older Wega 2 group espresso machine. Looks like a date of 1992 on the group head, but not sure. This has no model name that I can find. Anyway, when I turn it on I get all lights flashing after it heats up 5 minutes or so. I do get nice steam from the wands. I drained teh tank and found a little scale, but not much. I took apart the group heads and cleaned them thinking it may be a clog there, but that doesn't seem to have worked. Also fwiw the water level float is not visible and whe


For a new fridge, need more time to maintain the required temperature of the fridge abut mainly the goods in it? So everything seems normal. The time will be reduced day by day since the goods will stay for longer time in and door opening will bec ... Vacuums

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have an electrolux ultralux 80th anniversary edition that was over heating and shutting down. I took apart and blew out the dust now when I put it together it does not come on. I may have reconnected the wires wrong and do not have the manual. Where can Im get a manual?


... Electrolux UltraLux 2000 Bagged Canister Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

My Babylock Serger Eclipse was bought around 1994 and had a looper threading tool wire to thread it when I could not get it to thread manually. I lost the tool and can't get the thread to blow through. [email protected] thanks Karen


Try one of the Serger looper threading tools listed on this Amazon.com page: http://www.amazon.com/Serger-Looper-and-Needl ... Vacuums

I got my Mom's Kenmore sewing machine and I an trying to figure out how to get the scalloping and arrow head stitches to work. I have followed the manual and I can get all the other stiches but those two. It is a Model 1451 zig zag machine. I realize it is old, but the machine is just like new. HELP. Thank You.


... Vacuums

I bought this second hand, so have no manual for parts, etc. I smelled something really bad, am assuming it was the belt. How do i release the head of the vaccume to get to the roller. It needs cleaned anyhow.


Rotate the front belt lifter from green to red then rotate the locking knob above the nozzle. and the head will lift off. it helps if you put the height adjustment in the highest setting. did it smell like rubber burning? ... Kirby G5 Bagged Upright Vacuum

Broken Clip the clip that holds the contact head onto the wand has snapped. Where can I get a replacement clip? The original clips green but I'll take any colour.


Go to www. repairclinic.com and go to vacuum cleaners parts.or get helps via online chat.God bless you ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

How do i take extension wand # KC99PBZPZV06 apart.There is a electrical problem and i need to get to the wiring


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.


... LG Vacuums

My Powwer head on the wand burned up Can I get a replacement


Yes, you will have to contact sears with model. ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

My shark steam mop is not working properly cannot find manual what can i do i am in the older generation and not technical mop head is getting too wet or not wet at all. steam not even thanks


Google is your best friend. EVER ! http://www.sharkclean.com/cgi-bin/livew/site.w?loc ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have the dyson animal. There is something stuck in the wand tube and everyting is getting caught on it. There is very little suction from the wand. How do I get the wand apart or somehow get the object stuck out of the tube? Thanks


Yes, things stuck in vacuum hoses are not always as easy to remove as one might think. Trying to push it out with something can be counter-productive, and only get the thing stuck tighter! If you have a second vacuum, you can try sucking it out the w ... Vacuums

Electrolux EL7024A vacuum power head wiring


... Electrolux Vacuums

Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.


Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums

Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!


Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum

I have a kenmore progressinve 22813. The hose ripped at the swivel head. I purchased a new hose but can't separate the old hose from the swivel housing. How do I do that? do i need to buy all the swivel head parts as well? Thanks


Usually when you remove the hose from the swivel base and try to attach the new hose the attachment is usually not tight enough therefore the suction is always low. It is better for you to purchase the swivel head parts to enable you enjoy the use of ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

I had a manual, beung disabled, prop[le come over a help clean and put stuff away, but now the problem, is the vacuume won't stay put together and i can't find the damn manual, is it possible to get another it's a bissell power force model un sure of can i get anotrher manual. thomas d. silvia


BISSELL User's Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User's Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file. ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0933 seconds