Having problems with your Eureka 109A Easy Clean 2IN1 Cordless Stick Vacuum ?

The machine shuts off after 2 - 3 minutes. Turning it off and back on gets about 10 secnd run. The batteries are NOT discharged. Have to it off and back on repeatedly ot finish the job.

Answers :

The problem is not the battery pack. It is in the electronic over current circuit that prevents a possible overheating of the battery pack. My unit will run for 10 - 15 seconds and then shuts off. The over current sensor is reset by moving the power switch to the "OFF" position. If you turn the vacuum back on it will run for a few more seconds before shutting off again. There is a small circuit board in the vacuum that contains the over current protection circuit. It uses an NXP Semiconductor HEF4001BP quad 2-input NOR gate. If you are good at soldering you might try replacing this chip. Otherwise, buy a new vacuum. The problem is not in the thermal circuit breaker located in the handle. I have bypassed the breaker and the problem still occurs.
Repair Help & Product Troubleshooting for Eureka 109A Easy Clean 2IN1 Cordless Stick Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The machine shuts off after 2 - 3 minutes. Turning it off and back on gets about 10 secnd run. The batteries are NOT discharged. Have to it off and back on repeatedly ot finish the job.

The problem is not the battery pack. It is in the electronic over current circuit that prevents a possible overheating of the battery pack. My unit will run for 10 - 15 seconds and then shuts off. The over current sensor is reset by moving the pow ... Eureka 109A Easy Clean 2IN1 Cordless Stick Vacuum

I can't get the vacume to run for more than 15 minutes before it shuts down presumably do to overload. But I don't get the warning light and I clean it out regularly. I have to let it sit for hours until it resets and I can finish the job

Sounds like you have a blockage. Check your attachment hose by dropping something through it, if it is all clear, then check your duct hose, this is the hose at the base of the cleaner. Many times this will clog and you might have suctionat your ho ... Vacuums

I installed a new battery in my Roomba 540. It charges and runs directly with power cord but will not charge on dock. When I push the dock button, it acts like it "sees" the dock and approaches it and even slides on, but then gets back off again and just keeps going back and forth until I turn it off.

... Roomba Robotic Floor Bagless Vacuum

I have had a Hoover Linx cordless stick vac for several months. Even after charging the battery the vacuum will not run at all. What are potentially the problems and how do I get it fixed.

... Hoover Platinum LiNX Cordless Stick Vacuum

I have two dogs and while vacuuming on the back stroke I get a black line of dog hair. I have to keep running back over the same spot to finally get it up. It doesn't do it on the forward motion, .

That's natural.. vacuums pick up the dirt on the back motion (going against the grain) ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a irobot roomba 560, that doesnt go back to dock for charging, he just runs until the battery runs out? What can I do to make it go back to the dock ?

... iRobot Roomba 560 Robotic Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard

Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks

CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

I have an Electrolux Silverado deluxe canister vacuum that won't run. It was running fine, I turned it off to move the plug and then it won't turn back on. It is getting power to the switch. Any help?

... Electrolux Vacuums

Just put a new battery in scuba and it runs about 30 seconds (completely charged)

1) replace again the batteries by new ones and completely charged.2) test the charger if if functioning properly, can be faulty, and not charge well the batteries.3) test the power supplies inside from the scuba, to due some short circuit dra ... iRobot 5800 Scooba Vacuum

The Lifesaver smoke alarm model 1225 is hard wired, no battery and is chirping. I have it pulled out with wires coming out of the back, but can't open the front face to get in to disconnect the wire. Anyone know how to open it up?

Hi, you should be able to grasp it and twist it to open/remove it from the juntion box to expose the 120 volt wires. They do not open like one with a battery type, so twist it I believe CCW to remove it from the box to disconnect the wires. Please be ... Vacuums

Not charging After being on the charger for a long time, 24 hours, it barely starts to run, then increases spead some but not enough to pick up. Can I get a new battery or is it just a goner?

There could be reasons for this. \015\012\015\012Firstly check the air waves of the hand held unit by inspecting the slide out built in crevice part - if its clogged - remove it.\015\012\015\012Secondly, check the brush roll a ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

Elkay drinking fountain M#erpb28c continuously runs, having problems getting mounting nut back onto bubbler, seems basin should come off for access, however needind a reapir manual or access instructions to make repairs..please help

The Elkay fountains are turned on by a solenoid powered valve. There is a rubber grommet in that valve assembly that gets holes in it and then water gets behind it, causing the valve to stick on. To test that it is a solenoid problem, turn the wate ... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum

Have a 3 year old Pfaff Creative Vision. Has less than 14 total sewing hours on it. Has had issues in the past. Breaking needles, wouldn't stitch out designs in acceptable manner(badly distorted looking) breaking needles repeated, now it is changes stitches on its own, then went to sewing the same stitch but isn't sewing it consistantly. I have taken it back to the same professional to repair each time. Can thhis machine be repaired??? Should I trade it off and get another, this isn't my first c

It sounds like this machine has some kind of fault in it for sure. It can be repaired again, but will likely need to be repaired again after that - down the road. Personally I recommend you just get rid of this unit and go for a different model. Y ... Vacuums

Roomba would run for 2 seconds and then stop it Plays 4-note song as Power button blinks RED. if I remove the battery and then try again, it repeats the same.

Probably, the battery has little service life left and should be replaced. You might let the machine run until there is no light showing at all, recharge fully, then try using it again. If you know someone that has a similar unit, try swapping batter ... Roomba Robotic Floor Bagless Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.

There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

Hi. DC14 not running. Repeated pressing of the switch occasionally produces a split second whirr from the motor. I had been picking up plaster dust for some time but stopping regularly to clear out filters and 'the little tubes.' The switch is fine. I cannot see how to get at the motor. Thanks , Chris

Hi again. I finally figured out access to the motor. One of the brushes was burnt and broken. I have ordered a replacement set and cleaned up the comutator ( spelling ?). Thanks, Chris ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a swivel sweeper, the original series, that is about one year old and is losing power. The battery has been replaced but it still seems weaker than it used to be. The brushes do not turn as quickly and the overall pick-up is not as strong as it was when it was new. Any suggestions on how to get the power back up to what it once was?

HiThank you for your queryI think what you will find is the base of the sweeper has 4 brushes, each of these brushes are run from a cog, if you can take the base apart you will find that it has been clogged up with hair and ot ... As Seen On TV Swivel Sweeper Vacuum

Engine troubles I have a 1975 4x4 GMC full size van. The motor is a 350 cid small block on propane. The thing hadn't been running in 5 years and when I tuned it up I changed vacuum advance pod on HEI distributor and hooked to a better vacuum and now the hotter it gets the faster it idols and when I try and turn the timing back, it starts hard. Wondering if vacuum is too strong or what is up?

I haven't fixed it yet but I think I might have a solution for it. From the factory this thing had a 4 barrel carb and they put an equivalent size atomizer in it for the propane and over the years someone omitted the EGR system in it and propane is a ... Vacuums

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????

Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

It acts like it has a short in the hose you can hear the motor running and then it will quit. Moving the hose around you can get it to turn back on.

Hello. There is either a short or a poor contact at some location within the hose. In order to fix this you may have to replace the power hose. Joe ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a whirlpool personal valet steamer system that is mounted to the wall. The system was in the house when I purchased it so I would suspect it's about 8 - 10 years old and I cannot find the manual for it. When I push the start button it automaitcally cancels the set up and will not run. I have unplugged it for a while and then put it back in and it's worked before but not anly longer. How do i get a manual or can I find a repair person to look at it.

... Vacuums

Took apart to clean (all stopped up). cannot get it back together and running.

Take it to a reputable Vacuum Store in your area Be honest tell them what you have done to it.\012GOOD LUCK ... Bissell Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0631 seconds