Having problems with your Eureka 12 Amp Capture Vacuum Upright Vacuum ?

Eureka capture model 8803 type AVV...runs for 10 minutes then stops. will not re-start for a long time.


Answers :

This could be a few issues. First it could be the thremel swith located inside, or it could be the carbon brushes also located inside. If you are a do it yourselfer you can purchess the carbon brushes from any vacuum repair shop. The thermal switch should be tested before replacing "thus- you shoud have a local repair shop look at" I would find one that offers free estimates so they can diog. the problem. then buy the part and start the fun part. Saving big $$$$$$
Repair Help & Product Troubleshooting for Eureka 12 Amp Capture Vacuum Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka capture model 8803 type AVV...runs for 10 minutes then stops. will not re-start for a long time.


This could be a few issues. First it could be the thremel swith located inside, or it could be the carbon brushes also located inside. If you are a do it yourselfer you can purchess the carbon brushes from any vacuum repair shop. The thermal switch s ... Eureka 12 Amp Capture Vacuum Upright Vacuum

Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian


... Electrolux Vacuums

My iRobot Roomba 560 starts spinning sporadically during the cleaning, and after over 3 minutes it complete stops and beeps 9 times. It is necessary to turn it on until it decides to work properly, and keep waiting for the next time the same failure will occur. I tried to reset it, and I have all the dust removed including from the bumper and sensors.


It's the bumper. Blow it out with compressed air and clean the cliff sensors. If you still get the 9-beep error, call support. ... iRobot Roomba 560 Robotic Vacuum

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Hoover the on-off switch could be the problem will start and stop by itself. model is u2440-900 series is zh12.0 1200.60hz 12.0.a this product is easy to handle havent had that long of course made in china


A common problem with hoover vacuum cleaners is that a wire breaks inside the insulation just where the power cable enters the machine body causing the erratic on off situation you describe.\015\012\015\012There is a connector box inside ... Hoover Vacuums

Roomba model 4210 starts and stops after a few minutes only going in short distances and then turning allthough it hit nothing...


Inside this Roomba, the cleaning head module is clogged badly with debris. Open up your Roomba and remove all debris. ... iRobot Roomba 4210 Bagless Robotic Vacuum

I have the eureka capture vacuum and it works great; however, it has recently started making an extremely high pitched sound when I use it. It is still vacuuming but the noise is so loud it hurts my head and I can only vacuum for a few minutes at a time before I have to turn it off. What is wrong with it???


Dust is getting past the dust cup filter, to the motor. Call Eureka customer service. 1-800-282-2886. ... Eureka 12 Amp Capture Vacuum Upright Vacuum

Model DC-31 Animal. Brand new out of the box. Brush turns intermittently at initial start-up then stops completely after 30 sec. to 1 minute of using. Belt is in-tact and functioning. Belt motor hand-turns with some resistance felt.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.


How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you


Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Two weeks ago, my 4150 roomba stopped during running and sounds "ehh". every time i hit the clean button it sounds "ehh" and doe'snt work. at the first time it did it ,i have cleaned the sensors then it start moving forward and backward until it stopped . from now on it only sounds "ehh".


EHH sound:-------\015\012Cliff sensors are dirty or need repair.Try cleaning the sensors and check.If still the same problem then the sensors needs to be rechecked and its connections has to be replaced.\015\012You can try this opt ... iRobot 4150 Roomba Vacuum

Keeps stopping. My Roomba Discovery says it has a full charge, but it runs for a few minutes, then stops and beeps and the status light comes on. If you press the clean button, it will start again and go for a few minutes before the same thing happens again.


Your battery isn't holding a charge ,buy a new battery ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

My dyson dc 16 hand held vacume stops & starts while in use, each time you pull the trigger it will start again but then stops after a short while untill i pull the trigger again.


Cutting out can be due to a few things , motor overheating due to dirty filter, Faulty mains cable or plug..sealed type also..Faulty Switch/trigger.May need to seek pro help to fix. ... Vacuums

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.


Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

My Electrolux model C151D runs for 30 secs and then stops, starts after 1 min and stops


... Electrolux Vacuums

My roomba backs away from docking station then starts to go then stops and spin left then stops and spins right after a few times stops and beeps many beeps. What is the problem


It sounds like the 9-beep error. You can fix it by buying a repair kit from www.eesolutions.ca. I fixed mine in about an hour and a half. ... iRobot Roomba 530 Robotic Vacuum

Problem starting Sometimes will not start at all. Sometimes will do a quick start and stop. Other times it starts and runs fine????


This can happen if you have an intermittent short in your cord. Try plugging it in and then wiggling the cord around where it goes into the body of the vacuum with the switch set to "on." (If you're not sure whether it's on or off, just click it back ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vitamix 5000 stopped working. It stops working each time I use it; while blending I first smell a burning smell and then blender stops and will not start again. After sitting overnight it works again next morning and repeat same process. Any ideas how to repair?


It has an internal thermal shutdown. Let it sit for a while and it will reset itself. You can expedite by putting the motor base in the freezer for a few minutes, or by blowing a hair dryer into the base of the motor. ... Vacuums

I have a vacuum cleaner model Z5245 and the flexible hose keeps sucking together and stopping suction. This is the bit with the stop start controls on it. How do I repair this or replace it?


If theres a clog, then youll have to remove the entire section of hose from the vacuum and use a non blunt stick - bamboo sticks are excellent for this purpose. Stretch the whole hose out and put the stick down the hose until you can wriggle the stic ... Vacuums

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

I have an Amana above range Radarange, Model #AMV4204AAB, Serial # 10168958GE. Tonight after running for a 7 minute period and finishing, it would not again start. There is power to it, but various buttons no longer work. The following buttons won't work: Kitchen timer, Light Timer, #5 button, Popcorn, Poultry, Auto Defrost, and the Start button. Any help?


Hi,\015\012\015\012Push\015\012the power cord all the way into the outlet in case it became loose and\015\012is causing the problem. If the microwave still isn't working, check for\015\012a blown circuit fuse, and repair it ... Vacuums

Using my Proheat bissel 7901 I wil hear a popping sound than suction will stop. The machine can run for long periods of time or short time before it happens, what could it be?


Clog in the suction side somewhere the pop is the safety as to not burn up the motor. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0694 seconds