Having problems with your Eureka 12 Amp Capture Vacuum Upright Vacuum ?

What is the best way to clean the filters ? Is there an awners maual online? I need to know how to take this apart to clean it all well.


Answers :

May I get the model # so I can help you more
Repair Help & Product Troubleshooting for Eureka 12 Amp Capture Vacuum Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What is the best way to clean the filters ? Is there an awners maual online? I need to know how to take this apart to clean it all well.


May I get the model # so I can help you more ... Eureka 12 Amp Capture Vacuum Upright Vacuum

Cleaning! To clean the cyclonic cone Dyson say to use can-air? that may be ok for computers but not to blow out the dirt and dust from the cone in question. Someone else here suggested to use a real compressor! Well dahhh I knew that! Should I do the blowing in the living room? or may be in the bathroom? Seriously what I need is an assy. drawing to take it apart and washing it Any ideas where I can get one? Thank you John


Hi, we realy love our Dyson, but get frustrated when it gets clogged with pet fur (2 cats and 2 dogs). This takes a little effort but what we ended up doing was taking the vacuum apart into its major components and alternately blowing it out, filter ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Hoover Steam vac has also stopped sucking... I have pulled it apart to clean it. Is there a way to take the bristles off to clean them as well as are there any other parts that could be the problem?


Based on your description, poor suction is related to only a few things\015\012\015\012Check filter inside lower tank\015\012Check the lower tank lid to be on properly\015\012 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


You did not identify your model and the TriStar website does not provide manuals. They do have a FAQ page which does provide some illustrated guidance which may be helpful. See here:\015\012\015\01 ... Tristar Vacuums

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


... Tristar Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

NEED TO CLEAN CAP OF THERMOS VACCUM HOW DO I TAKE IT APART WITHOUT BREAKING IT?


... Thermos Vacuum Insulated 24-Ounce Stainless Steel Hydration Bottle Charcoal 24-Ounce

No suction I live in a house with two bernese mountain dogs... very large animals who shed a LOT.  I've cleaned the filters, the roller, and gotten as far into the hoses as I can without taking the entire machine apart.  It's still not cleaning as well as I know it can... nothing is making it into the debris receptacle.  What can I do?


Hi elora,\015\012\015\012I live in a house with three shedding cats. I also have the same vacuum. About twice a year, I have to getinto the area of the vacuum where the motor is. There is a little pring loaded vavle that sometimes gets ... Bissell 3590 CleanView Bagless Upright Vacuum

I need an operational manual for a beam central vac model 178. It came with the house and I need to take it apart and clean it. Does the filter thing inside the system come off. It is caked in dust and dirt and I think it is effecting the performance of the vacuum.


... Vacuums

My hoover vacuum runs for about 10-15 minutes then the saftey feature shuts it off(overheat?). i have taking it apart a cleaned it with no results, added new bag also. after an hour it cools down and works again. do i just need a new vacuum?


Do you have suction through the tools? Does it look like it picks up when it runs? The machine could be clogged and that would cause the problem, but unfortunately the sensor that shuts the machine off could be bad if the machine isnt clogged. Its no ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a kenmore whispertone 300, model 116 28612791, serial # DH0809803. I need to take the power head apart to clean it but can't figure out how. I don't have the manual for it. Is there a page of instructions I could print out? Thanks Lisa Coster [email protected]


... Kenmore Vacuums

I need to take apart my Kenmore Progressive Bagless Upright with Inteli-Clean System


What problem are you trying to fix? The is no belt so you don't need to remove the bottom plate. If you are trying to remove the main hose, remove 4 screws on the back and remove the plate. There are 2 more screws under that. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Need to take apart a Bissell Big Green Cleaning machine to replace pump


... Bissell 1672 BIGgreen Wet/Dry Vacuum

I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.


This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum

Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.


Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum

Kenmore upright vacuum model 116.35923500. not rotating when on. Easy way to clean without taking apart?


There is a switch that tells the cleaner that the upright is locked \015\012upright and the beater bar won't spin until you depress the foot release\015\012 and tilt the cleaner. This switch mount is poorly designed, its just \015\012sitting in a poc ... Kenmore 22812 Bagged Canister Vacuum

Had to take bissell 8910 completely apart, need reassemble instructions


... Bissell ProHeat Pet Upright Deep Cleaner, Purple, 89104

Dirty filter caused vacuum to swtich off mid-use. Filter's cleaned, but machne won't start again. Is there reset switch or do I need to take it in to get fixed?


... Westinghouse WST1551 Wired Deluxe Upright Vacuum

Found old Hoover "Concept One" and need to take it apart


... Hoover Vacuums

Taking tank apart to clean Dyson07


At the top of the cyclone there are three screws, these are the star type so the correct driver is needed, this will be easy to get with a full set of electric screw/drill fittings. Anyway, very carefully take the three screws out and slowly lift off ... Dyson DC07 Bagless Upright Cyclonic Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

Vacuum has new bag but won't pick up dirt. Cleaned flat filter and it made it worse. Do I need to replace rectangular filter or can I clean it. If so , how? If not, do I need to take it in for repair, ir should I get new parts? Thanks!


It's clogged somewhere. Disconnect the hoses where you can and check for obstructions. Run a coat hanger down the hose if you need to to clear the obstruction. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0819 seconds