Having problems with your Eureka 1934 Bagged Upright Vacuum ?

Eureka 1931 bagged upright, I changed the belt but now the cover is rubbing against belt. How do I prevent this?


Answers :

If your cover is rubbing, you probably put the belt on wrong. It should line up with the belt close to the groove in the underside of unit.
Repair Help & Product Troubleshooting for Eureka 1934 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka 1931 bagged upright, I changed the belt but now the cover is rubbing against belt. How do I prevent this?


If your cover is rubbing, you probably put the belt on wrong. It should line up with the belt close to the groove in the underside of unit. ... Eureka 1934 Bagged Upright Vacuum

Sudden loss of suction. Using a dirt devil upright. Checked the belts that were changed recently and working. Changed the half full bag. No change. Checked for blockages and as far as I can see there are none. The blower is working as much as it ever was I think but I;m stumped.


R u sure there is nothing cought in the hose? ... Dirt Devil Featherlite Bagged VacuumVacuum

Change belt on hoover savvy bag and bagless upright vacuum


... Hoover U8155-900 Savvy Bagged Upright Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

HOW TO CHANGE A BELT - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum


Hi there...You will need a Phillips screwdriver to get the bottom cover off.Remove the screws and then remove the bottom cover.Clean out any excess dirt in the general area of the roller bar and motor assembly area.Place one end of the belt over the ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

No manual, how do you change the belt? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

Change belt on oreck xl intellashield - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Have eureka victory upright bag vacuum model 4325 how to get into machine to change out the belt


There are four holes on each side of the top of the hood. There is a screw on each side, inside one of those holes. You have to take those two screws out to remove the hood. ... Eureka Vacuums

Hoover Elite upright is making a very loud noise. I changed the bag, cleaned the roller and checked the belt. What else can I look at?


... Hoover Platinum Collection Upright Vacuum

How do i change my belt on the kirby g6 - Kirby G6 Bagged Upright Vacuum


Hello,For detailed, step by step instructions (with pictures):http://www.goodvac.com/articles.asp?id=143Hope this helps! Ple ... Kirby G6 Bagged Upright Vacuum

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks


Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do you change the belt? - Oreck XL Ultra Bagged Upright Vacuum


Two methods:\015\012\015\0121) If your vacuum has the small side door on the cover of the lower unit, can remove the screw, it will allow you to access the belt. I assume old belt is broken, so what you see will be the end of the motor sh ... Oreck XL Ultra Bagged Upright Vacuum

Belt change for model #u4258-930 - Hoover Runabout U50-940 Bagged Upright Vacuum


Hi,This link will take you to a site with instructionsand illustrations to help you change your belt.http://www.info-vacuum-cleaner.com/hoover-va ... Hoover Runabout U50-940 Bagged Upright Vacuum

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.


Its still clogged, you gotta dig deeper ... Vacuums

My vaccuum has lost suction. I changed the bag and cleaned everything out. The vaccuum is only 6 years old. I even replaced the belt around the brush. When I turn the vaccuum on it smells like burning rubber. My vaccuum is an upright 12 amp model #33000300C serial #Y347012385


... Kenmore Vacuums

Change belt in hoover turbopower 1500 vaccum - Hoover U5046-930 Turbopower Bagged Upright Vacuum


... Hoover U5046-930 Turbopower Bagged Upright Vacuum

Dirt Devil upright doesn't have suction. I changed the belt and the bag. The suction is so slight it won't pick up a small piece of paper. The accessory wand also does not have much suction.


Try cleaning chute that fills bag.may be obstruction blocking the flow of air ... Vacuums

How to change g5 belt - Kirby G5 Bagged Upright Vacuum


1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off) \015\0122)Remove the power head from the front of the machine. Now turn\015\012the belt lifter the other way and line the green ar ... Kirby G5 Bagged Upright Vacuum

How do I change the belt? - Eureka Smartvac 4870 Bagged Upright Vacuum


Turn the vacuum over so the bottom is up.. Remove scews from plate surrounding the brush area..\015\012Pop of the cover plate..\015\012Lift out the side of the brush that the belt connects to..\015\012Put new belt on..\015\012 ... Eureka Smartvac 4870 Bagged Upright Vacuum

Change the belt - Eureka Smartvac 4870 Bagged Upright Vacuum


Hi There,Here's how you can replace the belt on your Eureka SmartVac 4870. I have taken pictures of the repair to help you better with this.Here's what you'll need in order to complete this repair:- ... Eureka Smartvac 4870 Bagged Upright Vacuum

Changed belt. have burning smell - Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum


Take it back apart, check it again. Check the plastic where the belt is running for burnt spots. Also check the brush roller sometimes the tension from a new belt can finish off what was left of the bearings and cause the plastic end caps and roller ... Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum

How do I change the belt on a dyson dc33? - Dyson DC33 Bagged Upright Vacuum


This link is for the manualhttp://support.dyson.co.uk/medialibrary/Files/Dyson/Support/downloads/UK/fl ... Dyson DC33 Bagged Upright Vacuum

Changing the belt - Hoover U6434-900 Bagged Upright Vacuum


... Hoover U6434-900 Bagged Upright Vacuum

Change the belt on a Kirby - Kirby G4 Bagged Upright Vacuum


CHANGING THE BELT ON KIRBY G3 G4 G5 GSIX ULTIMATE ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0732 seconds