Having problems with your Eureka 2271 Bagged Upright Vacuum ?

Motor for Eureka upright model 2315, new in 1977

\015 I'd like to order a new motor for my old Eureka upright model 2315 purchased in 1977. It uses the F&G bag.\015

Answers :

If the motor is obsolete which it appears to be, have you considered repair?

Write my shop at [email protected], with enough information on the failure mode we can get you a close estimate, some of these older vacuums just cannot be beat, for performance, power, etc, We traditionally do not do retail work, but with the current conditions, and woodburning stove blowers rendering perfectly good stoves into land fills, and replacement costs of over $3000,. we have repaired many blowers and fire eyes from $50.00 to $159.00, it all depends on the degree of damage, but we are trying our hardest to salvage some very nice older equipment, let us know, references or see me at allexperts.com. Will Babbitt
Repair Help & Product Troubleshooting for Eureka 2271 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor for Eureka upright model 2315, new in 1977

If the motor is obsolete which it appears to be, have you considered repair?Write my shop at [email protected], with enough information on the failure mode we can get you a close estimate, some of these older vacuums just cannot be be ... Eureka 2271 Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.

Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.

Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

Very loud motor - Eureka Altima Upright Vacuum Model 2996AVS Vacuum

If you are sure the noise is comming from the motor, either the fan on the motor is damaged and now not balanced or the bearings are bad. If it's a year old or less you can get it repaired under the guarantee at a Eureka Nationwide service center. Pr ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Removed and reinstalled motor on Eureka model 6426a. Now power switch position 1 is dead. Power Switch position 2 works fine,

... Vacuums

Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.

I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down

... Eureka Vacuums

Model DC-31 Animal. Brand new out of the box. Brush turns intermittently at initial start-up then stops completely after 30 sec. to 1 minute of using. Belt is in-tact and functioning. Belt motor hand-turns with some resistance felt.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

Need manual for Eureka Powerline Plus Model 9730 Type A - missing "door" that covers tool access port on body of upright motor...any ideas? This causes dirt to fly out unless tool hose is placed in "port"--don't always want to use tools, just main vacuum.

I found it at www.vacpartswarehouse.com for $4.79 + sh ... Eureka Powerline LiteSpeed 5845 Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Eureka 9410 upright vacuum motor

... Vacuums

Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.

You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Eureka altima model 2993 how to change belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum

... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t

... Vacuums

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.

If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a

... Electrolux Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

I have a kenmore canister model number 116.2645083 I need a replacement motor. I was given 2 different numbers: 1. 4147248 2. AC92FAUX200 I can find the 2nd motor, but it doesnt have the 4 wires like the original one. Can you tell me if this is the right motor? Thanks Becky

Greetings from GoVcauum.com,\015\012\015\012Ok, so good news, I have looked up your model number for your Kenmore vacuum and found that your Kenhmore canister takes the motor ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

What belt is used for a Eureka upright Model 2025B vacuum cleaner? What is the diameter (or the circumfrence)? of the round belt

... Eureka Electrolux EL5020A Intensity Upright Vacuum Cleaner

I have a eureka model 5190. The motor starts then

... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Motor replacement for upright Eureka 4467av

Part # is 60261-11, but Eureka has it No Longer Available. But check with a vacuum repair shop, they should be able to order one for you, but they cost around $80 or so. ... Eureka 4467AV Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0855 seconds