Having problems with your Eureka 2961AVZ Bagless Upright Vacuum ?

Brush roller stopped rolling

\015 The roller stopped rolling. At first it was stopping and starting and then it just stopped all together. I took the cover off to make sure the belt did not bust; it was fine. I removed, cleaned, and reinstalled the roller and then it worked for a few minutes but then stopped again. Any suggestions?\015

Answers :

My daughters is doing the same thing and the plastic at the ends of the brush bar melted just enough for it not to turn properly. You might want to chech that.
What I can suggest is taking the cover off and taking off the belt. Then turn the vacuum on and see if the upper spindle the belt goes on (not the roller) is turning. I think it could be two different things, but I'm guessing your belt is slipping. They just get slick inside and don't turn the roller. You can clean the spindle and roller where the belt attaches (I recommend isopropyl alcohol and q-tips), also try cleaning the inside of your belt, but if that doesn't work try replacing the belt. See if that works.
Repair Help & Product Troubleshooting for Eureka 2961AVZ Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush roller stopped rolling


My daughters is doing the same thing and the plastic at the ends of the brush bar melted just enough for it not to turn properly. You might want to chech that. ... Eureka 2961AVZ Bagless Upright Vacuum

Dirt devil plat.force brush roller wont roll on carpet


... Dirt Devil M091200 Platinum Force Upright Vacuum

The roller brush stop working


The fuse in the plug may have blow so replace it any ways ... Dyson Ball DC24 Bagless Upright Vacuum

Brush roller on Hoover upright stops turning


There should be a belt tensioner for the V belt, maybe it is not contacting the belt when you tilt the handle back. If this is less then 1 year old, then it is under warranty, take it in to a warranty servicer for warranty repair. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen


Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

My Brush Roll Stops when lowered


Hi There,\015\012\015\012            It sounds like you ready for a new belt, It needs to be a Genuine Knurled belt which has dimmples on this inside for extra grip.\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Bissell Momentum roller brush doesn't roll w/ pressure


This is going to sound funny, but check the wheels. Sounds like the pin or shaft that holds them is broke. Also check the tension on your belt. If the tension is to loose then the brush will have a hard time spinning.Good luck ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee


Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this


... Vacuums

Brushes stop rolling when against carpet, yes it is out of the upright position and when I left the base off the carpet the brushes start to roll again. What is wrong?


Your belt is stretched out so it just stops when the carpet resists it. Get a new belt made for your particular machine and you should be back up and running ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??


... Oreck XL Ultra Bagged Upright Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?


I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

Bissell Lift OfF Brush Roller Stops Rotating


They make the worst machines, the rollers are cheap and they make it so you cant take them apart to clean them. You don't want a dyson either, they aren't any better for pets. With all that hardwood floors you should get a good canister vacuum, sebo ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Roll brush stops on contact with carpet


There could be a problem witht the tensioned. Take off the top cover and try to see why it isn't pushing the belt when the handle is tilted back. Hopefully the belt is in the proper position, I have seen where the belt was put on the wrong side of ... Vacuums

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha


You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

Bissell Vacuum brush stopped rolling


The belt may be broken. Consult the user manual or locate on the sole plate or front hood when getting to the sole plate. Usually it involves a few cross head screws on the base of the vacuum cleaner where the roller beater bar is. Remove that and ch ... Eureka 2961AVZ Bagless Upright Vacuum

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.


... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

My dirt devil easy lite cyclonic does not suck up the dirt or anything on the floor anymore the rollers still roll. It stop sucking.


Check and make sure that the pickup tube from the bottom of the sweeper to the waste cup does not have a clog anywhere you can use a metal coat hanger and straighten it out and carefully run that thru. ... Vacuums

ProForce 1500 has suction but the brush roll motor stops working.


... Proteam ProForce 1500 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0463 seconds