Having problems with your Eureka 2991AVZ Bagless Upright Cyclonic Vacuum ?

How do you replace the belt? Can't find anyplace to open the bottom to replace belt.


Answers :

You don't actually have to turn the vacuum over for this. The two screws you need are on top, above the brush roller. It is the top cover that comes off instead of the bottom on this vac. You'll see everything once you lift it off.
Repair Help & Product Troubleshooting for Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you replace the belt? Can't find anyplace to open the bottom to replace belt.


You don't actually have to turn the vacuum over for this. The two screws you need are on top, above the brush roller. It is the top cover that comes off instead of the bottom on this vac. You'll see everything once you lift it off. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt


On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How do i replace belt, i cannot find screws to open up, i have no manual


Hello. The screws are either on the bottom, the part that hits the floor, or under the rubber bumper. Find the screws, remove them and remove the base or cover to expose the belt area. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

How to remove bottom panel on eureka 4325 victory for belt replacement?I can not find screws.


... Vacuums

Hoover turbo power 1500 have part of bottom off to replace belt but can't find where to attach it? must be more parts to take off but how?


... Hoover Elite U5061-900 Bagged Upright Vacuum

I have a eureka the boss smart vac petlover vacuum and I cannot find the book on how to replace the belt. I have opened it up, but there is a silver roller that is confusing me.


Either go directly to the Eureka internet site, or GOOGLE "eureka boss smart pet lover manual". Several options should be displayed to download the needed manual. ... Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey


... Electrolux Vacuums

I need to replace belt but can't find where belt belongs,only says belt access. can't find belt.


Not easy to read, but this URL might be of assistance to you:\015\012\015\012http://canada.bissell.com/images/UserGuides/9500_107.pdf\015\012\015\012Please let me know if it does not help you. My assistance is free and I am more than wil ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a hayward 1HP superpump with an Ao Smith UST 1102 motor on it. Last year I had a leak in the pump, and I believe I got some water in the bearings of the motor. Over the winter I replaced all the seals in the pump, and have no leaks this year, but the pump is sounding pretty loud since opening the pool this year. I have (2) fold question: (1)I can not find any information on the where I can find a replacement bearing for this pump. (2) I can not find a procedure on HOW to go about


Hello. I get my parts here http://www.poolcenter.com/parts_pumps_hayward_superpump.htm\015\012\015\012Joe ... Vacuums

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.


If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike


... Hoover Vacuums

Replace belt on fantom cyclone vacuum? the manual does not decribe replacing the roller belt - i can't get it open to expose the belt


On my 10-year-old model, the two screws securing the cover are under the two llight bulbs. Pry off the clear plastic covers, take out the bulbs and screws, and the cover lifts off. ... Fantom Vacums Cyclone XT Upright Vacuum

Need to replace power cord and can't find how to open canister to replace


I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

Replacing Belt Can't find the manual and it's time to replace the belt. Can someone help with instructions. Thanks!


On the front of the power head is a knob with the KIRBY name on it. Rotate this knob in a counter clockwise direction and it will "lift" the belt off the motor spindle. Release the head lever, only one direction it will turn and remove the head. Tur ... Kirby Ultimate G Bagged Upright Vacuum

I have the same rproblem with my little Shark V15Z hand held vacuum. the belt broke,there's no instruction on how to replace (and apparenlty it was not designed to be replaced (at least with out a lot of research). I see BElectric describes how to find the hidden path, but now where can we buy the correct belts??


... Euro-Pro HEPA Shark EP035 Bagless Handheld Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

Where does it go and how do I replace the belt on a Deluxe Hoover Mach 3.8 bagged windtunnel action vacuum? I kno it goes somewhere around the brush but it fell off when opened and I can't tell where it goes. I have a replacement belt


... Hoover Vacuums

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My belt broke and I cannot find a replacement anywhere. Can you tell me where I can buy replacement Sweep n Groom belts for my central vacuum system.


You can get replacement Sweep n Groom belts here:\015\012\015\012Sweep n Groom Belts ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0767 seconds