Having problems with your Eureka 3041BZ Upright Vacuum ?

Roller brush does not engage, don't know how to access belt. Brush does spin freely.


Answers :

Flip the vacuum over for you can see the beater bar, remove all the screws in that bottom housing that are countersunkunk.Seperate the housing and see if belt is broke/stretched and very that the motor turns
Repair Help & Product Troubleshooting for Eureka 3041BZ Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller brush does not engage, don't know how to access belt. Brush does spin freely.


Flip the vacuum over for you can see the beater bar, remove all the screws in that bottom housing that are countersunkunk.Seperate the housing and see if belt is broke/stretched and very that the motor turns ... Eureka 3041BZ Upright Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?


Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??


... Oreck XL Ultra Bagged Upright Vacuum

The roller brush underneath is not spinning when the vaccum is on, it does spin freely, I'm thinking maybe there's a belt inside that may have come off?! Is it easy to fix or replace this?!


Power drive windtunnels need to be serviced about once a year. Take it to a vac shop. Your belts need replacing and idler pulley needs adjusting ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a eureka 4351 and I think the belt is broken but I can't figure out how to access it to check. Roller brush doesn't spin though. Just need to get the silly thing apart.


... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.


Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

When we changed the belt the new belt broke right away and the brush roller wouldn't spin. My husband cleaned off the roller and got it moving slowly again, but when we went to re-attach everythin


The thing you call wheels are actually called roller bearings that fit at both ends of the brush-roll there probably seized up you can get a new brush-roll with bearings from the link below. ... Dirt Devil Breeze Bagged Upright

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]


You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

No spin Vacuum's brush does not spin on (low) carpet unless switched to "high" but then roller does not pick up hair on carpet. Belts are in good condition. Maybe belts are loose?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=782631\015\012No spin\015\012Posted by erin_david on Jul 14, 2008\015\012Vacuum's brush does no ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt


... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

When I engage the beater roller it will work for a short time (15-20 seconds) and then squeel loudly as if something is not engaging properly. I checked the roller ends and cleaned them but it seems to roll freely by hand while connected to the belt and then at a time it becomes very hard to turn by hand.


Sounds to me that the motor is shot. There is a main bearing the belt shaft connects to and it sounds like the bearing is seazing and gets worse when it nheats up. Soon it wont turn anymore at all ,once it siezes completely. These are rarely worth f ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this


... Vacuums

Beater brush won't spin but belt is intact and ok. Brush is clean and spins freely by hand.


For your beater brush to spin, you have to meet two conditions:\015\0121) the vacuum cleaner has to be reclined (put your foot on the front and pull back on the handle).\015\0122) The clutch actuator (the dial where you switch between BEA ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.


It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

My vacuum's rug brush will not spin. the belts are fine and in place, but when i engage the carpet brush nothing happens. i looked under the bottom and there are no obstructions preventing the brush from opporating/


Have your clutch checked out by a local vacuum repair shop. That's a common problem with dyson brush rollers ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Hoover steamvac model f-5883-900. The brushes spin freely when i spin them myself,but dont spin when running. The vac runs but sounds differet like a higher hum. To fix this would the pin be broken or the turbine


... Vacuums

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?


... Vacuums

Hoover steamvac model f-5883-900. The brushes spin freely when i spin them myself,but dont spin when running. The vac runs but sounds differet like a higher hum. To fix this would the pin be broken or the turbine


... Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Its like the roller brush won't lower and it doesn't "engage" anymore. I posted this but input the wrong vacuum model ....not sure if that matters? I can vacuum and you still see footprints on the carpet. I have suction, just no brush action, yet the brush spins....


Sorry about that, I guess I have to post this as a solution in order for the pictures to display. Here's the entire solution on a similar problem that I've answered previously. Please let me know if you need help further diagnosing the machine, I ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushes are not spinning. think the belt is off or broken. how do i access the belt?


There is no belt in this machine. The brushes are turning by an air driven turbine. The turbine has a pivot bushing made of steel inside of it that gets rusty because of the water that is running through it. The turbine will have to be replaced an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0735 seconds