Having problems with your Eureka 3276AZ Pet Lover Bagless Upright Vacuum ?

I have a Eureka Pet Pal and I think I have something caught in the bar and is not rotating. How do I get to the bar to check?


Answers :

Repair Help & Product Troubleshooting for Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Eureka Pet Pal and I think I have something caught in the bar and is not rotating. How do I get to the bar to check?


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

I have a canister with a beater bar which i love. I have sucked up a sock (or something) in the beater bar and it will not work. I can't get it open to check it out. We have misplaced the booklet that came with it.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=820565\015\012Generic problem for all Vacuums\015\012I have a canister with\015\012Posted by DFundis on ... Vacuums

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

How do I change the belt on Eureka Pet Pal - Eureka 3276AZ Pet Lover Bagless Upright Vacuum


Unlike most vacuums, this one the screws are on the top of your base. There are two screws one on each side. When looking at the front of the vacuum right side screw is located above the s in 12amps and on the left side screw is located above the p i ... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.


Squealing ... Vacuums

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look


... Kenmore Vacuums

I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out


Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Bissell powerforce turbo, and my beater bar is not spinning, i have checked fordebris in the bar itself, but it seems one of the sides is not circle and it is getting caught on its little hole it fits into... so my question is.. Is it supposed to be circle? instead of oval shaped?


Usually the bar is driven by a belt--it may have come off or snapped and is broke. ... Bissell Vacuums

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.


... Windsor SR12 Sensor Bagged Upright Vacuum

Roomba. Diagnostic The brushes will not rotate. I have cleaned them, used an air compressor, and checked the front wheel. What can I do to get the brushes rotating?


Go to homesupport.irobot.com and get contact for help.and get the parts too.God bless you ... iRobot Roomba 560 Robotic Vacuum

INSTRUCTION MANUAL FOR EUREKA LIGHTSPEED 100 - Eureka 2 Type Dcf4-Dcf18 Upright Vacuum Cleaner Hepa Pleated Washable Filter W/activated Charcoal Whirlwind Mighty Mite Maxima Boss Power Plus Pet Pal Lightforce 300 Lightspeed 100 General Electric Ge 63073 4700 5500


... Eureka 2 Type Dcf4-Dcf18 Upright Vacuum Cleaner Hepa Pleated Washable Filter W/activated Charcoal Whirlwind Mighty Mite Maxima Boss Power Plus Pet Pal Lightforce 300 Lightspeed 100 General Electric Ge 63073 4700 5500

Eureka pet pal hepa filter vacuum - Eureka 2991AVZ Bagless Upright Cyclonic Vacuum


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

I have a windtunnel 2 vacuum. It sucked up a cord that wrapped around the beater bar. Now the bar won't turn. There was no smoke or sign of something burning. The motor still runs and there is suction but no turning. We have it apart but nothing is obvious. What should I check?


Check the actual beater bar for movement. I have seen the plastic melting, and bearings seized under such circumstances. Also I am unsure by your question, but the motor that creates the vacuum (sucking) is different than the motor that spins your ... Vacuums

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?


The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The Petmate powerhead roller stopped rotating. I checked for anything binding it - nothing. There is power getting to it, just no rotation. As the guy said in the post above, it's like it is locked into the plastic housing, although it just worked last time I used the powerhead. Help!


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Am attempting to get 'inside' the vacuum to troubleshoot why it suddenly stopped running. Suspect it may electrical, and have already checked the obvious (visible cord and plug.) However, there doesn't seem to be an obvious way to get inside the canister without destroying something. Thanks!


Hi There,\015\012\015\012Here's a link to a repair solution that I've done explaining how to diagnosis the cord reel, and open up the machine. The model this is done on is not the same exact model as yours, but the repair will be almost ... Miele S251 Flamenco II Bagged Canister Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

We have already spent $60 on getting the belt repaired once. This time, the same thing is happening, the belt is jumping of the small metal bar in the back of the housing. Seems like there should be something on the end of the bar to keep the belt on it?


Greetings from GoVacuum,\015\012\015\012Ahh, the Hoover Windtunnel Self-Propelled model. This model has a some reoccurring problems with it. The majority of them have to do with the b ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have removed the obstructions in the brush bar and the brushes still will not rotate. What else can I check?


Hi Genie, it's Jack at Dyson.Once you've cleared any obstructions from around the brush bar and inside the cleaner head, you need to reset the machine. This is easy to do - just press the button in the red recess on the side of the cleaner he ... Dyson Ball DC24 Bagless Upright Vacuum

I can't get the roller bar back in


The oval shaped ends of the brushroll have to be rotated to one side and rest on the wall of the brushroll housing, once you line this up your cover should fit on. also make sure to install the brushroll the right way with the belt on the molded ball ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson 17, the Absolute Brand special for pet hair. I think I have a blockage in the hose. Symptoms are: spewing out fuzz balls and small particles. I have checked all the blockage sites recommended by Dyson and all are clear except a small flexible transparent hose, 6 or 7 inches long, curled up underneath the cleaner head/brush bar unit. Any ideas? I've tried to pull out the stuff stuck in there, but I'm afraid to perforate the hose and I don't know any way to disconnect it.


Try dropping something like marbles into the hose and shake it up and down, may loosen it up enough to draw through.hope this helps you out. ... Vacuums

Kenmore progressive upright (direct drive) with bag has low suction and the beater bar does not rotate. Also, it is not obvious how to get inside the vacuum


Hi there,\012First of all you look for a reset button on the motor and press it in with cleaner plugged in and turned on, push the little reset button on the side of the lower base of vacuum. Remember that the brush will not turn in the u ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Scrubbing brushes I have cleaned the filter, checked the dial to make sure it is turned to high and cleaned all of the brushes. Still I can't get the brushes to rotate. What now?


Your turbine might need to be replaced ... Hoover F5881-900 Vacuum

I have the hoover automatic dual vac 5. this is the 3rd hoover rug cleaner i purchased and always the same problem the spray underneth the rotator bars hardly dispenses and the floor hardly gets wet, this has happened with all 3 rug cleaners


The carpet is not intended to get soaked, like what you see with a spray application. If you are seeing a stream of water in the nozzle/tank during the recovery stroke, this is working properly. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0978 seconds