Having problems with your Eureka 3276AZ Pet Lover Bagless Upright Vacuum ?

The roller is not turning after i caught up a frayed carpet string.


Answers :

This could be because of 2 things on this model.

1) the model MAY have a white reset button on the side of the unit that the hose does not go into. Sometimes to prevent a toothed belt from damaging the motor.

2) the belt may need to be changed on the unit usually noticed with a burning rubber smell when you caught something. this just requires a belt change.
Repair Help & Product Troubleshooting for Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The roller is not turning after i caught up a frayed carpet string.


This could be because of 2 things on this model.1) the model MAY have a white reset button on the side of the unit that the hose does not go into. Sometimes to prevent a toothed belt from damaging the motor. 2) the belt may ne ... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Caught shoe string in roller brush, now will not rotate roller BR


Belt maybe streched and hardened from heat replace and try again. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Roller does not turn; I was vacuuming a rug and a string got stuck in roller-took it off but now the roller will not turn. suction is fine.


The roller drive belt may be stripped, worn partway through where it goes around the motor shaft, thrown off the motor shaft, or broken. Take the bottom plate off the carpet sweeper and have a look.If the belt was damaged when the roller ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?


... Eureka Smartvac 4870 Bagged Upright Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.


Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Carpet function rollers don't turn


Most likely a broken belt. If the brush roll is turning freely, then check the belt. ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Carpet roller will not turn. Vacuum still sucks up dirt


It IS true that you can take the plastic cover off the top of the carpet head. But in addition to removing the two Phillips screws at the bottom, you have to manouver the wand release a bit. Loosen the screw and carefully pull the release back just a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Carpet roller brush will not turn


You probably need a new belt. You can get kenmore belts here:Kenmore Belts ... Vacuums

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

Dyson dc 23 animal. the roller in the head will not turn when the vacuum is flat on the carpet as though it is sealed to the carpet


... Dyson DC23 Animal Vacuum

Vacuum won't pick up any dirt - there's no roller marks when vacuuming carpet. Roller does turn and filters are clean.


Hi,\015\012\015\012When you turn the roller, you should feel some resistance from the belt. Remove the base blate that surrounds the beater bar. Check the belt. Take care in removing the beater bar, so you can get it back in the same w ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Rollers won't turn when on carpet, ok if I lift the vacuum above the carpet.


That is very strange. So when you lift it up above the carpet the feet / wheels turn freely, but when it is on the carpet it won't move at all? Not even when you push it, the rollers won't turn, but when you lift it up it does? That doesn't make m ... Bissell 3920 Bagless Upright Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

My bissell 9400's brush rollers do not stop turning. When I was using the hose attachment for the stairs the handle was in the upright position and the brushes kept turning. Also water was leaking out of the rear right side onto the the carpet under the machine.


... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?


You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.


The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

Eureka Boss 4870 -Brush roller won't turn on carpet and turns when its not supposed to (with handle in upright postion). New belt had burning rubber smell right away.


... Vacuums

Dyson 07 The roller does not turn. I cleaned hair and string tangled but it still won't turn. How do I check if it is the belt?


Start of by laying the machine on its back unfasten the solepate (which\015\012is the cover over the brush roll) as soon as its unfastened it will\015\012release with ease then you will see the brush roll with the belt around\015\012it simply pull th ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I got a plastic bag caught in the DC17 Dyson Vacuum. It will not turn now. I do not think it is the belt, as it is there and not broken. The belt and/or the roller is not turning


You need to remove the plastic bag.thats stopping everything ... Vacuums

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

When I turn the carpet switch on for Shark Navigator, it will grab the carpet when I push forward, but will not when I pull back. Any ideas what the p? I cleaned the brush roller of all hair/fuzz and no change.


... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

I have the Electrolux Intensity upright vacuum. The roller bar underneath that is used for carpet no longer turns. I have checked the belt that is attached to it. I'm afraid that it may be the motor. Where can I take it for service or shat do I do now? Kay


... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0530 seconds