Having problems with your Eureka 3276AZ Pet Lover Bagless Upright Vacuum ?

How do you replace the belt on the pet power paw vacuum

Answers :

1. Pry off adjustable clear cover with flathead screwdriver.
\0122. Unscrew 2 Philips screws holding power paw together.
\0123. Place tips of needle nose pliers into the two holes on each of the black round pieces on the ends of either end of the roller. Twist and the black pieces will release.
\0124. Remove roller, use needle nose pliers or awl to dig out any hair wrapped up in the roller or especially the ends of the roller at the metal pins.
\0125. Replace belt and put everything back together in the same order you took it apart.
Repair Help & Product Troubleshooting for Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you replace the belt on the pet power paw vacuum

1. Pry off adjustable clear cover with flathead screwdriver.\0122. Unscrew 2 Philips screws holding power paw together.\0123. Place tips of needle nose pliers into the two holes on each of the black round pieces on the ends of either end of t ... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Shark vacuum nh15 replacement pet hair power brush replacement

... Euro-Pro Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Belt replacement Does Hoover Windtunnel V2 model # U8148-900 even take a belt? The owner's manual only describes how to change belt in powered hand tool, not the vacuum itself.

No belt- it is motor driven. what happens to these if the rollers get stuck(by- say, a Lego® or something)  is the roller itself has an insert which will break, requiring roller replacement. \015\012\015\012simple fix, but costs a ... Hoover WindTunnel V2 U8148-900 Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Need to replace belt in Kenmore Vacuum Power-mate nozzle

Hello,\015\012\015\012Here's what you'll need to replace a belt on a Kenmore canister vacuum:\015\012\015\012- Phillips Head Screw Driver\015\012- Flat Head Screw Driver\015\012\015\012There are two different ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Roller got power cord. This stretched out the belt. I replaced the belt, now the vacuum is making a noise. Cant find anything wrong, what could be making this noise?

Most rollers have several different positions you can install the brush in check and make sure the roller height is equal. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.

Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Broken belts I have had my vacumm for about 3 months and have had to replace the belt twice, is there anything i can do to make this stop? It is an Eureka True clean 12 amp multipath cyclonic system. it has the pet paw on it and the telescopic self cleaning duster. thanks

... Eureka 4467AV Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Looking for new belt for my electrolux guardian canister vacuum power nozzle marked model n106m . have been unasble to locate an appropriate belt replacement. Any suggestions?

This company is now known as Aerus. If you can't find their listing in the local yellow pages, follow the instructions on the folloing site.\015\012\015\012 ... Electrolux Guardian Bagged Canister Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?

There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

I have a GE 106766 Canister Vacuum. The belt on the power end stretched and I replaced it. Now the roller froze up and won't move. Where can I find a replacement roller?

Try this sitehttp://www.onlinevacuumparts.com/ps-328-7-ge-6850-106766-canister-power-nozzle-parts.aspx ... GE 106766 Bagged Canister Vacuum

How to replace belt on a eureka boss vacuum - Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

If you look on the base plate you should see a diagram of how to do it,but if yours don't have a diagram then remove the screws from the base plate it should be three or four they have arrows next to them. take the base plate off and remove the brush ... Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions

If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

I have to replace the power cord on my Bissell upright pet hair eraser vacuum because it is damaged from getting run over by the vacuum. Familiar story? Rather than pay a technician a lot of money, I feel I should be able to tackle this myself (went to college and everything). What are some pointers to help me bravely tackle this without the help of a male (no offense guys)?

Of course, its simple.\015\012Use electric tape to make sure the wires never touch, usually a phillips screwdriver will do to uncscrew the machine.\015\012just make sure you line up the cords the right way, positive to +ve and negative to ... Vacuums

I need to replace a belt on the shark infinity pet care system upright vacuum. I have the belt I need a manual to show me how to put it on

... Euro-Pro NV31 Infinity Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I need to know what kind of belt to replace the original with. It's a Eureka Multipath (yellow) Cyclonic with a pet paw and telescopic self cleaning duster

... Eureka 4467AV Upright Vacuum

The power paw on my vacuum doesn't work anymore and also when should the hepa filter be replaced and how is this done

... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Change fab belt on vax power pet 1 - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I need a replacement belt for my central vacuum power nozzle.

Do you know the brand or model? If not you can get replacement central vacuum belts here:\015\012\015\012Replacement ... Vacuums

How do I replace the power brush belt? - Bissell 8910 ProHeat Clear View Upright Vacuum

This machine needs to be taken to a dealer to replace the belt. It is hooked into the pulley and pump assembly and is a nightmare to fix. ... Bissell 8910 ProHeat Clear View Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1123 seconds