Having problems with your Eureka 3276AZ Pet Lover Bagless Upright Vacuum ?

Don't know how to replace broken belt on eureka pet pal upright bag less put one on broke immediately

\015 One just put on broke immediately\015

Answers :

Repair Help & Product Troubleshooting for Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Don't know how to replace broken belt on eureka pet pal upright bag less put one on broke immediately


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

I have an L shaped piece of metal with a hole at one end that fell out of my hoover elite bagged upright vaccuum cleaner. I repaired the belt but don't know where this metal piece goes. I think it has something to do with the wheel assembly which is replaced and it seems to want to stay there. any thoughts


This metal clip was for the wheel assembly, but not always needed. you can diregard the part if your vac is working correctly with the front wheels. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of


Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Not sucking i have a KIRBY G3 that was working great. One day there was a strong smell and the brush roller belt broke so I replaced it. The fan looks good. Now the vacuum does not **** up dirt but instead seems to very gently blow air forward. I took the (new) bag off and it is blowing hard int the bag. I am stumped!


Belt is not connect to the drive pulley, see manual for fitting or see utube for video ... Kirby Generation 3 Bagged Upright Vacuum

I have a Kirby Heritage II Turbo and I need a user's manual, but can't find one anywhere. I have to replace the fill tube in the bag and can see the cable tie on top that holds it in place, but don't know how it's attached to the mini-emtor. If I can't replace the fill tube, will tape fix it? If I just taped it; will it hold? Thanks.


Taping usually just causes a mess. The mini-emptor has coarse threads on it that the fill tube screws on to. Occasionally there is a cable tie on the bottom which is not really necessary. If you cut the tube near the bottom, you can get hold of it's ... Kirby Heritage II Vacuum

Belt broke I have a bissell powersteamer and a belt broke and came out the bottom of it. I dont know how to put one back on it


There should be an access panel on the top side of the cleaner. Pry this open with a screw driver and this should get you access to the area where the belt can be changed. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

When the bag was changed a tip broke off the bag holder and I would like to buy a replacement part but unable to locate one


... Vacuums

The bag latch on my Kirby Generation 3 broke. How do I get the old one off to replace it


At the bottom of the bag, there is a zip tie around the plastic part that turns & snaps on to the exhaust hole of the vac. also take a flat screwdriver & pull up the rubber under the zip tie...all the way around, like u would take a bike tir ... Kirby Generation 3 Bagged Upright Vacuum

The little toothed belt on my bissell shampooer broke got a replacement but don't know how to put it back on Stark's where I bought the belt wouldn't help me man said he isn't a mechanic. well neither am I so could you send me a diagram I could follow? Thanks


Hi!  Your question has come up under Bissell ProHeat, although you don't actually specify that model. Assuming it is, the belt change operation is quite simple but hard to describe in words (it will sound much more complicated than it actually i ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

I need to replace the torsion spring on to the valve arm that controls the valve door. I just need a explanation as to how the spring is connected to the two parts. This is for a Hoover U6632900 upright bag-less series.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The wheels with the spring broke off and I'm trying to put a new one on but I don't know where the spring goes.


This spring can be very confusing to install. It slides onto the wheel assembly near where the attaching pin is longer ( there are flat protrusions on both sides of the wheel assembly). One end of the spring pushes up on the assembly when it is in pl ... Hoover Tempo Widepath Upright Vacuum - Blue

No water or shampoo coming out, or no sucksion. Also, belt broke and I am uncertain were to put the replace one?


Follow lthe ink below on how to replace the belt. If the belt is broken the brush will not spin and the unit will not spray.\015\012htt ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The clip that connects the water base to the top of the suction area broke off..where can I get a replacement base (the part where you put the water in and has the bag where you also store the dirty water)? I have a Bissell proheat 2x


Here is the number for Bissell, they can tell you who to contact near you.\015\012Service Center Dept. Phone Number:(800) 457-1509Service Center Dept. Fax Number:(800) 517-9535Hours:M-F 8:0 ... Bissell Vacuums

Sunbeam water dispenser YLR2524H2 - the hot water lever broke and I need to know if I can get a replacement part and can I install the new one myself?


... Vacuums

I am trying to replace the pump belt on my Bissell Proheat 12 AMP moedel #7901-9. I was told this was the easy one to change, but it is only if you know where it goes and how to put it there. Can you give me some help? Pam


Here is a link to where you can view the manual. Hope it helps!Bissell ProHeat Belt and Manual ... Vacuums

The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?


You can buy Hoover Handle Release Lever 38434-021 at \015\012http://partsreadyonline.com/item.php?ItemID=798 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I purchased a toastess vacum bag sealer at Canadain Tire two months ago. I only had it about a month when the sealing wire broke. I returned it to the store and they replaced. One month later the same thing happened again, but because it is more than 30 days I can not return it to the store this time. I have misplace my bill of sales. Where do I go from here. Carmel Whiffen Marystown NL AOE 2M0 (709)279-3149


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=578564\015\012Generic problem for all Vacuums\015\012I purchased a toastess vacuum\015\012posted by carmelwhiffe ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1332 seconds