Having problems with your Eureka 402A Bagless Upright Vacuum ?

No sucking the brushes spin fine, but the vacuum does not suck up things, is it worth fixing?

Answers :

Could be that the dust cup filter is clogged, part #60958, or the inlet down by the brush roll is clogged.
#402 not much suckion ,cleaned every thing
Repair Help & Product Troubleshooting for Eureka 402A Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No sucking the brushes spin fine, but the vacuum does not suck up things, is it worth fixing?

Could be that the dust cup filter is clogged, part #60958, or the inlet down by the brush roll is clogged. ... Eureka 402A Bagless Upright Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.

You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush is not spinning, vacuum is not sucking.

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.

Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I was vacuuming, and ran over an area rug with those tassle things on the end. the brush immediately stopped spinning. so i turned the vacuum off and un-tangled the brush. after replacing the brush and putting the assembly back together, the brush no longer rotates.

Did you smell something burning? You probably melted/broke the drive belt. ... Dyson Ball DC24 Bagless Upright Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.

I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush spins, motor heats up, container doesn't spin anymore, not sure if it is "sucking up" anything ..had it for less than a year. Why won't it vacuum? dirt devil 12 amp HEPA filter vacuum

Probably clogged, or filters are very dirty ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.

- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

My dyson dc animal's brush is not spinning. The machine smells like burning rubber. I believe the clutch has gone out but the machine also only sucks from the top of the hose in the handle. I am wondering if the machine is not locking properly which is causing the brush to not need to spin. If this is the problem how do i fix this problem.

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?

Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Luv300b vacuum brushes won't spin. The belt is fine but still not working. Any suggestions?

... LG Electronics Kompressor Plus Upright Vacuum Cleaner LUV300B

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

My oreck vacuum has stopped sucking up things.

It won't turn the brush because the belt is stretched or broke from the heat of sucking something too big up. If you have your service manual it should show you the location of the belt covers to replace it. ... Montgomery Ward Oreck XL Celoc Hypo-Allergenic Vacuum Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?

Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'

HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

My vacuum's rug brush will not spin. the belts are fine and in place, but when i engage the carpet brush nothing happens. i looked under the bottom and there are no obstructions preventing the brush from opporating/

Have your clutch checked out by a local vacuum repair shop. That's a common problem with dyson brush rollers ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Same thing, brushes dont spin unless vacuum is tilted back

I had the same problem. Checked the belt, pulled out all the hairs, cleaned the hoses, but the agitator brush wouldn't spin at all or only marginally. Finally I removed the agitator brush altogether and found crud and accumulated in the small groov ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I by accident sucked up the corner of a sheet into the powermate of my vacuum. I turned the vacuum off and pulled out the sheet but now the powermate is no longer working (suction works fine) Is this something I can fix on my own?

These power heads have a kill switch on them. Not exactly clearly labeled. the kill switch reset button should be on the right side of the unit as you look down like you are using it. you may want to try pushing it with the power to the p ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My carpet cleaning brush does not turn on. The vacuum cleaner works fine but the the carpet cleaning attachment does not get any power so the light does not come on & the brush does not spin

... Kenmore 25512/ 25513 Progressive Canister Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?

The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1478 seconds