Having problems with your Eureka 411A Upright Vacuum ?

Metal clip and white piece came out of base when removing roller

Answers :

It really isn't the slot next to the wheel. It is the slot under the pivioting part of the body on the right side.
Repair Help & Product Troubleshooting for Eureka 411A Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Metal clip and white piece came out of base when removing roller

It really isn't the slot next to the wheel. It is the slot under the pivioting part of the body on the right side. ... Eureka 411A Upright Vacuum

When I took the base cover off the vacuum to clean the roller, a metal piece that is bent in half, as well as a white plastic stick piece came flying out. I think it might have to do with holding the vacuum in an upright position, but I don't know where it goes. Help!

They go in the slot beside the right wheel. Metal spring first, (the open ends facing away from front of vacuum base. The white nylon piece lays parallel and directly on top of the metal spring, round edge up, and aligned with the open ends of the me ... Eureka 411A Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher

If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

The belt keeps coming off. There is a little U shaped metal piece that came off when the belt first came off. Where does it go? When we first got the vacuum, we sucked something up and the belt came off and that little metal piece fell out. The belt now periodically comes off when we bump something. Please help us!!!!!!!!!!!!

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Eureka smart vac roller won't turn because a piece of metal inside it pressing on the roller

... Eureka Smartvac 4870 Bagged Upright Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?

Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I have a EuroPro Infinity NV29 and I have a clog in the base. I have removed the screws and the plastic piece where it says access port to remove clogs but don't know how to get the hose lose to empty it.

... Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg

Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

There is a blockage occuring at the first bend right above the roller brush.It appears to be caused by a broken piece of white tubing within the black tube/

Hi Vstanle,you have diagnosed it correctly, the best solution to your issue is to have the part replaced which is available from the link below. ... Oreck XL2200 Bagged Upright Vacuum

Norelco razor 6867xl - am planning to replace battery pack. Would be easier to solder if I could remove the whole circuit board system from the hard plastic case. How do you release the metal clips?

The whole circuit board is removable, and I would recommend removing it from the whole external case to work on so nothing is damaged by your soldering iron.\015\012\015\012Battery : 2x NiCd AA\015\012Battery capacity : approx. 700 ... Vacuums

The small screw-in plug (below 2-in-1 water tank) was removed in error, and the small plunger, rubber stopper, metal ring and spring came out. In wat order are they to be re-set within the such that fluid can be released correctly instead of all fluids coming out at once?

The metal ring goes first then the spring "Sits" on that washer, the plunger goes into the spring, then the rubber stopper goes on the end. OK. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

After vacuuming over a thick strand of loose carpert my brush roller will not turn on its own. The piece of carpet was removed easily and the belt is not broken. Your assistance would be helpful. Thanks

Make sure you can spin the brush by hand. The belt got hot and glazed when the carpet was stuck and will need replaced. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I changed the belt on a Eureka WhirlWind superlite, all was well but I can't seem to find where this white piece of plastic approx.2" and less than 1/2" wide and there is a copper like V shaped clip, I was hoping maybe you's had a diagram or something showing where these go. Much Appreciated

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552328\015\012Generic problem for all Vacuums\015\012I changed the belt on\015\012Posted by hiphoppy69 on Apr 28 ... Vacuums

Thread brakes sometimes it stops i think the trhead is not being led correctly since a little peace of metal looking like a clip or hook came off

Hmm ok I can help you with this but need to know the make and model of the unit in question.\015\012\015\012Thanks\015\012Tim ... Vacuums

How to change the bag in the Oreck XL hand canister vac? I can't seem to get the plastic piece back in before locking with the metal clip. Is there a diagram to show me?

... Oreck Vacuums

Hi I have a eureka 410 series lightweight upright and I took it apart to clean the dust from inside and on the very bottom of the handle the is a metal clip and a white straight plastic peice that fell out and I dont know how it goes back in.

... Eureka Whirlwind 410 Bagless Upright Cyclonic Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa

Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

I took the roller off my cleaner model 8910 and the black pieces came off as well and now I cant get them back on properly

Place the black brush arm onto the brush (the arm has a stand up pin / spigot which needs to be located into the centre of the brush) and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original p ... Bissell 8910 ProHeat Clear View Upright Vacuum

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4

One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do you install the 210-1128 Bissell carpet cleaner steamer brushroll on the Bissell ProHeat 8910? The prong on the replacement roller is larger in diameter than the one it is replacing. How do you open it up enough to remove the plastic piece that is attached to the steamer - the one with the belt??

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

My Kirby G6 light is not turning on when I start the machine. I took off the front piece and removed a lot of hair from the roller and interior. Since I did that, the belt keeps coming off (even though it is fairly new). Is that the reason the light won't turn on? Is there any advice you can give me before I take it in?

The light indicates that the brushroll is spinning. If it isn't coming on, the power nozzle may have been reinstalled incorrectly. Take the nozzle off and then use my step-by-step guide to reinstall it. I expect that it will take care of the problem. ... Kirby Vacuums

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.

I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0712 seconds