Having problems with your Eureka 431A Optima Bagless Upright Vacuum ?

I cant open it - Eureka 431A Optima Bagless Upright Vacuum


Answers :

Before doing anything, make sure that the vacuum is unplugged from the outlet. After that, you are now ready to open your vacuum. Here are the steps to do so:
a) First, remove the dust cap by pressing the "cup release" button on the top rear right of the cleaner and pulling the dust cap away from the top. Set aside.
b) These first three steps are optional, but will make the process a bit easier... Now remove the hose attachment by twisting the base of the hose clockwise until the tabs line up and allow you to easily remove. Set aside.
c) Now remove the floor nozzle attachment by depressing the silver lock button located on the bottom back of the cleaner. While this is pressed in, pull the body of the vacuum and the carpet cleaning nozzle away from each other. (This is easier with two people, but can be done alone.) These steps will make the cleaner less bulky for you to take apart and work with.
1) Now on the back of the cleaner, you will see 9 screws. (3 on each side of the rear of the body, 1 on each side of the rear base of the body, and 1 in the middle of the hose actuator valve [the knob that switches between floor and hose]). Unscrew all of these and set them aside. *see note at bottom
2) Now that these 9 screws are removed and placed aside, you will now be able to remove the rear panel of the vacuum. Do so and move it out of your way. Keep in mind that the power cord runs through a hole in this panel and cannot be removed entirely without disconnecting wires (which I wouldn't recommend if you don't know what you're doing).
\015\012\015\0123) Now on the inside rear of the cleaner, your should see 1 screw in the top right holding the power cord in place. 1 screw below that on the right side holding a number of white and black wires in place. There will be 1 screw on top right of the gray plastic that the floor nozzle had attached to, and 1 on the bottom left. There are also 2 screws at the same height (1 on the left and 1 on the right) about a\015\012quarter way up from the bottom screwed into the green plastic on the left and right of the gray plastic floor nozzle attachment. Remove these 2 screws.
4) Now look on the outside left and right of the base of the cleaner. You should see 4 screws (2 on each side). Remove these.
5) Now you should be able to remove the front panel to expose the motor which will be surrounded by black foam and resting in a circular hole in the bottom. Voila! You have now opened up your vacuum cleaner.

*Something to keep in mind before removing the screw from the hose actuator valve is to pay attention to the position of the knob. Also look inside the hole of the hose coupling while turning the knob to note how the valve moves inside the cleaner. When reassembling, make sure that this is in the correct position.
Repair Help & Product Troubleshooting for Eureka 431A Optima Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I cant open it - Eureka 431A Optima Bagless Upright Vacuum


Before doing anything, make sure that the vacuum is unplugged from the outlet. After that, you are now ready to open your vacuum. Here are the steps to do so:a) First, remove the dust cap by pressing the "cup release" button on the top rear rig ... Eureka 431A Optima Bagless Upright Vacuum

What type of filter used my eureka 431a - Eureka 431A Optima Bagless Upright Vacuum


You need a dcf 10/14 you can find them at walmant kmart target lowe sears or eureka.com thru eureka they are 14.99 plus 7.50 shipping ... Eureka 431A Optima Bagless Upright Vacuum

Eureka optima motor burning smell - Eureka 431A Optima Bagless Upright Vacuum


... Eureka 431A Optima Bagless Upright Vacuum

Change belt on eurika optima vacuum - Eureka 431A Optima Bagless Upright Vacuum


This link is for the manual will give you instructionshttp://www.eureka.com/FileLibrary/d944cbc8479a49aeafd4f964eb4842df/77297.pdf ... Eureka 431A Optima Bagless Upright Vacuum

Where can i buy A NEW FILTER FOR OPTIMA 33.0 - Eureka 431A Optima Bagless Upright Vacuum


... Eureka 431A Optima Bagless Upright Vacuum

Hi, my vacuum wont **** things up anymore. - Eureka 431A Optima Bagless Upright Vacuum


Look for blockages in the intake passageways. ... Eureka 431A Optima Bagless Upright Vacuum

Parts list and diagram for eureka 431 type a - Eureka 431A Optima Bagless Upright Vacuum


... Eureka 431A Optima Bagless Upright Vacuum

Where can I get a replacement hose for the eureka 431A optima bagless upright vacuum


You could try Espares.co.uk if your u/k ... Eureka 431A Optima Bagless Upright Vacuum

Need to replace the filter - Eureka 431A Optima Bagless Upright Vacuum


... Eureka 431A Optima Bagless Upright Vacuum

Wheels are falling off - Eureka 431A Optima Bagless Upright Vacuum


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Eureka 431A Optima Bagless Upright Vacuum

Suction not working - Eureka 431A Optima Bagless Upright Vacuum


Clear the clog in the hose and you will be fine. You may have to disassemble parts of this machine to assure the clog is gone.\015\012\015\012Thank you for posting your question on FixYa.com\015\012\015\012Please vote\0 ... Eureka 431A Optima Bagless Upright Vacuum

Does a Eureka Optima bagless upright vacuum have a belt in it? Mine stopped working and then now the motor sounds strange. I cannot find a belt.


... Eureka 431A Optima Bagless Upright Vacuum

Eureka the boss upright bagless vacuum. how do i open it to get to the belt area? the brush seems stuck. it wont move


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=801547\015\012Generic problem for all Vacuums\015\012Eureka the boss upright bagless\015\012 ... Vacuums

How do I change the belt on my Eureka Optima Bagless upright vacuum?


You will need to remove the base of the vacuum at the brushes. There should be either 2 pull levers that will allow you access to the belt area that once you release these levers the complete base section comes off exposing the belt and the brushes. ... Eureka 431A Optima Bagless Upright Vacuum

I HAVE A EUREKA ALTIMA AND CANT CHANGE BELT - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The hood will come off if you loosen two screws at the front on top of the hood by the brush bar bit that is slightly raised. Then there's a screw to the left hand side of the upright either below the hose or duster area. Once all screws are undone, ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Eureka capture vacuum - Eureka 8802AVZ Capture Bagless Upright Vacuum, Telescopic Self Cleaning Duster, Power Paw Turbo With Riser Visor, Dual Powered Edge Kleener, Comfort-Gripped Oval Handle, HEPA Filtration, 15 Extra Wide Cleaning Path, 30 ft. Cord Length, UPC 023169120891 8802


... Eureka 8802AVZ Capture Bagless Upright Vacuum, Telescopic Self Cleaning Duster, Power Paw Turbo With Riser Visor, Dual Powered Edge Kleener, Comfort-Gripped Oval Handle, HEPA Filtration, 15 Extra Wide Cleaning Path, 30 ft. Cord Length, UPC 023169120891 88

Eureka4701bagless upright vacuum - Eureka 4700A Maxima Bagless Upright Vacuum


Dont know what the problem is but this link is for the manualhttp://dl.owneriq.net/b/b7517422-db37-404e-9da2-d898185942e5.pdf ... Eureka 4700A Maxima Bagless Upright Vacuum

Need manual for eureka 4700 A-1 vacuum - Eureka 4700A Maxima Bagless Upright Vacuum


... Eureka 4700A Maxima Bagless Upright Vacuum

Eureka pet pal hepa filter vacuum - Eureka 2991AVZ Bagless Upright Cyclonic Vacuum


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

How to change a belt on eureka vacuum 4903 f - Eureka Power Plus 4703D Bagless Upright Vacuum


... Eureka Power Plus 4703D Bagless Upright Vacuum

My vacuum does not pick up dirt, why? - Eureka 3276AZ Pet Lover Bagless Upright Vacuum


It's clogged somewhere, or the belt broke ... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Cut off while vacuuming - Eureka 4700A Maxima Bagless Upright Vacuum


If it went dead, and restarted after it cooled off, then check for a clog in the hose or the dirt inlet by the brush roll. If it won't turn on, you could have a bad switch, cord, motor or a bad electrical connection. ... Eureka 4700A Maxima Bagless Upright Vacuum

How do I change the belt on Eureka Pet Pal - Eureka 3276AZ Pet Lover Bagless Upright Vacuum


Unlike most vacuums, this one the screws are on the top of your base. There are two screws one on each side. When looking at the front of the vacuum right side screw is located above the s in 12amps and on the left side screw is located above the p i ... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

What size belt does a eureka whirlwind take - Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum


Hi,\015\012\015\012Your Eureka Whirlwind 4388 takes Eureka Style "U" Belts, Part number 54312. \015\012\015\012Here's a direct link back to that belt on our website if you need to purchase one:\015\012 ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Hi there Hi have a Samsung VCU2913 Bagless Upright Vacuum. The wheel at the bottom have a rubber where it is driven by for the brush to clean the floor. Where can I get this, its n new vacuum... now I cant use it. I am in SA , Pretoria


Go back to where you bought the vacuum and ask for a BELT. Take the MODEL # with you and buy 2. Always keep a spare ... Samsung Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1308 seconds