Having problems with your Eureka 4467AV Upright Vacuum ?

Eureka 4467AV overheats and shuts down after about 3 or 4 minutes of operation. I pulled all the filters to assure no blocked air flow. I assume the motor is not getting enough cooling air but i can't figure out why. checked bag for blockages as well as hoses. could the thermal protection have gone bad?

Answers :

Repair Help & Product Troubleshooting for Eureka 4467AV Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka 4467AV overheats and shuts down after about 3 or 4 minutes of operation. I pulled all the filters to assure no blocked air flow. I assume the motor is not getting enough cooling air but i can't figure out why. checked bag for blockages as well as hoses. could the thermal protection have gone bad?

... Eureka 4467AV Upright Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho

Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.

Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums

I have a new electrolux el7025a-r and it keeps cutting off while I am vacuuming. I am using the small powerhead on hard floors and I have checked the hoses for blockages and the bag is new. I can not figure out why it keeps turning off in the middle of a job.

The wands are notorious for going out on that unit. One or both probably need to be replaced. Try to get it done under warranty if you still have the receipt, but they shouldn't cost you too much if you can't. \015\012\015\01 ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My dyson dc08 has a loss of suction. A flap valve operates within a few seconds of startup which appears to divert air. I have replaced both the hepa and sponge filters but the problem persists. If there is another blockage where might it be? I cant see how to dismantle the airways to check more than the very obvious. Suggestions gratefully accepted.

You have used your Dyson too long without thorough cleaning - Here's how. Obtain a torx screwdriver, or a set of torx bits, you will need to select the correct size when you come to remove the screws. They are all the same, so you will ne ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!

Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

I have just replaced the bag in my miele and the indicator is showing that the bag is full. The air coming from the exhaust is hot and the machine is making a higher pitched sound as it does when the bag is full. When the hose is detached, the indicator registers as empty and there doesn't seem to be a blockage.

... Miele Vacuums

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.

Squealing ... Vacuums

My kenmore intuition vacuum seems to have lost suction and the check bag light comes on. the bag has just been changed (2x). cannot see if there is any type of blockage. any ideas? thanks. ps. only had this vacuum for 3 months.

If you bought it new then do not screw w it take it back to sears and demand a replacement or your money back Sears is very reasonable re this ... Vacuums

Sudden loss of suction. Using a dirt devil upright. Checked the belts that were changed recently and working. Changed the half full bag. No change. Checked for blockages and as far as I can see there are none. The blower is working as much as it ever was I think but I;m stumped.

R u sure there is nothing cought in the hose? ... Dirt Devil Featherlite Bagged VacuumVacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated

1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Orange light is on - bag/hose check and I can't figure out why. Bag is not full. What do I need to check on the hose?

May be plugged ... Vacuums

I have a vec-101 vax bagless cylinder vacuum cleaner,only had it a week and the blockage light has stayed on.i have checked everything and cant find a blockage anywhere,what is the fault? thanks

... Vacuums

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

Hoover Alyx Pets 2000w Hoover Model TC1208 001 Virtually no suction, have checked for blockages but cant seem to see any, however i can't remove the hose to check it. Any ideas?

Did you check the HEPA filter? I have the same problem with mine if I don't clean the filter after using it. It's a dirty job but helps for a while. ... Vacuums

How do I work a Salton vacuum bag sealer (Model BS-20)? I can not figure out how to get the air out of the bag.

This style of vacuum sealer has to use a special bag with a " dimpled " surface to let the air escape through the pinch jaws of the vacuum sealer.\015\012\015\012The folowing web site has bags and rolls that can be cut ro make any size of ... Vacuums

I have a Panasonic MC-E3011 and it won't ****. I have checked all the pipes from the beater to the inlet at the dust bag, and they are both clear, pluss the air comming out of the vent at the bottom of the upright (above the beater) casing seems abnormally hot. I have allso checked the the belt and beater bar and they are functioning A1 OK.

... Panasonic MC-V7395 Vacuum

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina

Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate

The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

The beater bar on my Dyson DC14 All Floors Bagles vacuum cleaner doesn't turn. There is no hair or thread caught up in it. All air-flow areas have been checked and there are no blockages that we could find. Any suggestions?

If it is not on the bare floor setting then you most likely have a belt issue it is not an easy fix I am sorry to say if your mechanically inclined I can tell you how to replace it. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Light saying bag full and clogged have changed bagand checked for blocks cant find anything.

OK - blockages are not always obvious (especially if they are deep within the flexible hose). One thing you can try is to remove the flexible hose from the top of the bag compartment and then switch on - if the red light goes out, there's a blockage ... Sebo Automatic X1 Bagged Upright Vacuum

My dc 05 isnt working and i cant understand why , i have cleaned all filters etc and i also changed the fuse on the plug , which after i didi that it attempted to start but then jus cut out again so i thought the fuse had blown again , so i checked the fuse but its working fine could there still be a blockage somewhere in it or is it something electrical which means my dyson has to go to the dump :(

Most common cause of this problem is a wire broken inside the flex, usually either just where it leaves the plug (easy to fix) or at the other end (more of a problem). In either case, this is no reason to dump the machine - it can be fixed at a fract ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0561 seconds