Having problems with your Eureka 4700A Maxima Bagless Upright Vacuum ?

How to change belt on Eureka maxima 4700a

\015 I have a eureka maxima 4700a and the brush is not spinning. I believe the belt is broke, but it happened when my wife used it. I lost the manual, so how do I check and change the belt? Have no idea how to take it apart to do so. Thanks\015

Answers :

Hey i had the same problem with mine, (standing over it and looking straight down) there should be two screws on the top of the yellow cover, one on each side, take those out and the yellow cover should easliy pop off. if the white ink is off the belt or the belt isnt tight than replace, once off just pop the wheel brush (which has the belt around it) up out of its socket and take off of the belt from the wheel brush and motor's metal pole, then put on the new one just like the old one was. let me know how it works out, [email protected]
My girlfriend had the same problem. The brush stopped turning. I unscrewed the two screws on the top of the front yellow plate and it popped right off. The belt had snapped. Looks like an easy replacement. Seems like a cheap vacuum.
Repair Help & Product Troubleshooting for Eureka 4700A Maxima Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to change belt on Eureka maxima 4700a


Hey i had the same problem with mine, (standing over it and looking straight down) there should be two screws on the top of the yellow cover, one on each side, take those out and the yellow cover should easliy pop off. if the white ink is off the be ... Eureka 4700A Maxima Bagless Upright Vacuum

Change belt on maxima 4704 - Eureka 4700A Maxima Bagless Upright Vacuum


If you don't see clips or screws the underneath (base), there may be be 2 screws on the top side that have to be removed. This will allow you to remove the bottom in order to replace belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

How do I change the belt on the Eureka Maxima 12 amp? The belt was removed before I got it, so I'm not sure where it used to be.


... Eureka 12 Amp Capture Vacuum Upright Vacuum

Belt is off - Eureka 4700A Maxima Bagless Upright Vacuum


You need to replace the belt. Over time they stretch and wear and then don't stay on and make it so the vacuum doesn't pick up well. Here is the belt you need and a manual you can view which has instructions: ... Eureka 4700A Maxima Bagless Upright Vacuum

I dont know where my Vacuum belt is located? - Eureka 4700A Maxima Bagless Upright Vacuum


The link below is the manual it will give you step by step instructions on page 19 how to replace belt and brushbar ..http://dl.owneriq.net/b/b7517422-db37- ... Eureka 4700A Maxima Bagless Upright Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

Changeing belt I have a Eureka Upright Limited Edition Model 4462D and can not for the life of me find my manual and can not find the screws to take off the plate to change my belt.....help!!!!!


On the top nozzle, there will usually is 2 screws holding the top done. There are slots or holes on each side near the front and the screws or in these holes. Remove them, remove the top cover and then you can get to the brush roll and belt. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

Changing belt - Eureka Whirlwind 5740


I tried the website for manuals but no luck. I called the toll-free # 1-800-282-2886 and got a rep right away. I gave him the model and s/n (lower bottom on the back side) and he walked me thru it. For the model I have, there are 3 screws to remov ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks


... Eureka Bravo II Bagged Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

Snapping belt The belt broke in my Eureka maxima model 4700 I replaced it and the brush did not move, and the belt just snapped again. What might be causing this?


... Vacuums

Eureka 437za belt change instructions


... Eureka Vacuums

How do I change the belt on Eureka Altima 12 v


Here is\015\012a link to the owners manual which has instructions and a link to the\015\012belt you need.Eureka Altima Owner's Guide ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How do I to change the belt on an eureka altima 12?


The belt is on the bottom right (looking at it from the front). the Eureka website does have the manual for download, http://www.eureka.com/service/manuals/8024 ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Belt change for eureka capture


Lie the vacuum down so it's completely flat, the back of it facing up. On the bottom of it, on the grey plastic, there are instructions. They say, to access the belt, remove the screws numbered 1, 2, 3 & 4. Then look at the four corners of the bo ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

How to change the belt on a eureka vacuum model


... Eureka Smartvac 4870 Bagged Upright Vacuum

How to change belt on Eureka Whirlwind


On the top cover, there are holes at the front on both sides, there is a screw on each side in one of the holes. Take the out, and the cover should come off, then you can get to the brush roll and belt. ... Eureka WhirlWind 4381 Upright Vacuum

How to change belt 4870MZ Eureka Smart Boss Vacuum


... Vacuums

Belt how do i change the belt on the bagless eureka boss widetrack?


There are a total of 6 screws - one is hidden under the right front wheel. pull the wheel assembly against its spring - it's under there. ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

I HAVE A EUREKA ALTIMA AND CANT CHANGE BELT - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The hood will come off if you loosen two screws at the front on top of the hood by the brush bar bit that is slightly raised. Then there's a screw to the left hand side of the upright either below the hose or duster area. Once all screws are undone, ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How to change on belt on eureka model # 2991 - Eureka 2991AVZ Bagless Upright Cyclonic Vacuum


Here is the belt you need and a manual you can view which has instructioins:Eureka 2991AVZ Belt ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

How to change belt in eureka altima vacuum - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Here is the belt you need to replace and the manual which has instructions:Eureka Altima Belts ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0440 seconds