Having problems with your Eureka 5849A Boss Bagless Upright Cyclonic Vacuum ?

Runs ok for 30 sec. then beltmoves off drive and

\015 Runs ok for 30 sec. then belt moves off drive and roller and jams\015

Answers :

I bet you that the endcap on the brushroll has failed. its a common problem on those and since that has failed it probably destroyed the brushroll housing.
Repair Help & Product Troubleshooting for Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Runs ok for 30 sec. then beltmoves off drive and


I bet you that the endcap on the brushroll has failed. its a common problem on those and since that has failed it probably destroyed the brushroll housing. ... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

My Sentria always runs in the drive mode and it is so fast it seems out of control. If I push the neutral pedal it stays in drive. I can push it the regular way when it is turned off, whether the pedal is in the drive position or neutral.


I sold vacuums for almost 20 yrs and the Kirby gets lots of complaints. The transmission that it has in it breaks as your has and they are costly.The best thing to do would be to take the maching to the local vacuum store(eg. sewing and vacuum are of ... Kirby Ultimate G Bagged Upright Vacuum

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A


This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

Malfunction 8 franke flair. I have removed the brewing unit o rings to free up the drive. Drive motor keeps over running the top and bottom limits hence gears grinding. Could it be the sensor on the back of the motor? What is it measuring? Any help appreciated


... Vacuums

Roomba discovery on full charge power up and it will run 5 sec power button then flashes red and roomba quits. I have tried removing battery and holding power button for 30 sec then charging same result


Unfortunately the batteries on the roombas can go bad and not hold a charge and need to be replaced, also you should check all the brushes and wheels on the bottom, if they are bound up it would stop the roomba from working. the two brush rollers can ... Vacuums

Hi my dyson hand held dc 16 runs for 10 secs then for 3 secs until you let it rest, then it does the samething again


Take it apart and look for some trash might be rapped around the motor,because if the motor heats up it will shut down to keep it from burning up ... Vacuums

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.


The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

When i switch my henry hoover on it works fine for exactly 50 seconds then switches of for approx same time then comes alive again for 50 secs and so on...driving me nuts.


... Vacuums

I replaced the powerhead drive belt. Now (2 times) while vacuuming the powerhead motor appears to run backwards. Because the metal pully which has left hand threads on it will backout / unscrew it self. Prior to this belt rerplacement it functioned properly. Thank You Bob


Look at your power head motor. If you see a fiberglass looking sleeve on the shaft where the belt attaches to it, you need to remove that. You can slip it off, chip it off, or break it off piece by piece. You can usually use pliers and break it into ... Rainbow 75th Anniversary Canister Vacuum

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t


... Vacuums

My kirby g4 runs and vacuums well, but the power drive has no effect


How do you change the belt for the self drive? (not the brush) ... Kirby G4 Bagged Upright Vacuum

Progressive drive bagless and beltless sweeper (purple) that has a burning smell when running, what could it be?


Most likely the brushroll motor which is located inside the brushroll. This machine is one of the worst designs produced by kenmore, usually the brushroll motor only lasts 2 to 3 yrs. ... Vacuums

I found a quarter in the drive system. I was able to get it out but now it only runs in reverse. how do i fix this?


Turn the belt over - rather - if it is a figure 8 configuration, reverse the direction. if it is in a straight configuration, it needs to be in a figure 8 ... Kirby Ultimate G Bagged Upright Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help?


I just fixed mine by cleaning the shaft that the spinning brushes is on. I used an eyeglass screw driver to tke out the screw. it is running great now. I didn't realize my brushes werent spinning at the time of my post. Cleaning this part seemed ... iRobot Roomba 4210 Bagless Robotic Vacuum

Power drive runs in reverse continuosly - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


See the instructional videos from hoover for troubleshooting:and use the common sense and logicallyHowever the motor can be faulty. or the control boardhttp://hoover.com/support/ ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?


Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

I have a model 116.35922 beltless drive vacuum. The agitator brush will not turn with the vacuum running and the handle down. The brush turns by hand and the reset button has not popped. Ther is nothing wrapped around the brush, but it does feel to have some resistance when moving by hand.


Wich bags for vacuum cleaner kenmore model 116.35922 ... Kenmore Vacuums

My Roomba Discovery will not do our carpet. It is a medium pile tan carpet so it should be OK but it runs for a little while then shuts down and beeps. It does not try to restart.It works well on floors. I have recently done a full tear down and cleaned the drives and brush transmission.


... Roomba Vacuums

4210 battery light is full charge. runs for 5 sec. and nedds to be recharge again


Roomba's are noted to catch dust inside inwhich they will not operate correctly. Remove the entire housing parts and clean out all existing dust in this machine. It will run much better ... iRobot Roomba 4210 Bagless Robotic Vacuum

I have an Electrolux LE canister. It runs for about 2minutes then shuts off for about a minute , then turns on again and it keeps repeating this routine!!! It is driving me nuts. What part do I need to replace? Apparently it is over heating. Please help. Thank you.


The LE has a thermal cutoff. If the bag is overfilled or a bag breaks and clogs the bag chamber the vac will over heat. This also happens if the hose, wand or neck of the power head is obstructed. Try dropping a coin through the hose, look thro ... Vacuums

I have a Bissell proheat 9200 T. The brushes engage when the handle is lowered. However they only turn for about 20 seconds then stop. If you turn the power off then on they run about 20 seconds again. It is driving me crazy!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum

Will only run for 2or3 sec. then shuts down. power is good


The problem belive it or not is a simple fix...if u are electronic minded,,\015\012\015\012you need to remove the collection pot / and the battery ..\015\012\015\012now where the serial number is are 2 screws bellow remove the ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

We have a Eurolab XR210 Robotic Vacuum, it has stopped working. The fan will run, but the wheels do not drive, the UV light does not work, however, it will work in Docking mode. Can it be fixed?


... Vacuums

Hi I have a Star Elite vacuum cleaner JCV8002 that is no longer holding a charge......it runs for about 20 secs....Help!


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0268 seconds