Having problems with your Eureka 5849A Boss Bagless Upright Cyclonic Vacuum ?

How do i take the roller brush out of my eureka the boss 4d

Answers :

Repair Help & Product Troubleshooting for Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I take off the roller brush on my Eureka Boss. Something is caught inside and I don't see any screws to remove the roller.

The screws are on the top. ... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

How do i take the roller brush out of my eureka the boss 4d

... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka the boss 5893A brush roller will not work

Is there anything jammed underneath.can you turn the brush roller by hand.if not then take it back where you bought it.sounds like you have a defective brush roller ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Roller brush will not turn on Eureka "The Boss Power Plus" 12 amp

Depending on the model there will be a couple of screws on the top plastic cover. The cover lifts off and the belt is then serviceable. On some models you will need to remove some parts on the bottom too to get the roller out.In any case just l ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum


... Eureka Boss Superbroom Bagless VacuumStick Vacuum

Eureka the boss 16.6 clean the roller brush

... Eureka Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.

The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

Eureka Boss 4870 -Brush roller won't turn on carpet and turns when its not supposed to (with handle in upright postion). New belt had burning rubber smell right away.

... Vacuums

My Eureka The boss Smartvac Model #4870 roller brush won't turn even on the highest setting and the belt smells hot. we took the belt off. How can you tell if it needs replaced?

Just by what you explained I can tell that it needs to be replaced. The belt doesn't have to be broken to need replacing, if it is stretched and worn then it will slip on the motor shaft and not turn the brush roll and get hot. Here is a link to the ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.

Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

How do I remove the roller on my eureka vacuum,(world vac, mega boss

... Eureka Mega Boss 4460DT Vacuum

Eureka Wide Track Superlite vacuum roller brush motor

Don't know if you can find something that will work, Eureka doesn't make these motors available thru them. Try some local shops or a place that sells small motors. ... Eureka 431A Optima Bagless Upright Vacuum

How do I remove the brush roller onthe eureka clean living vacuum model no 3281 AZ

... Eureka Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Eureka 4870GZ vacuum: carpet/bare floor switch does not work, so now roller won't spin. can i repair this myself or do i need to take it in? if i need to take it in, what's the cost?

... Eureka Smartvac 4870 Bagged Upright Vacuum

My brush roller stopped spinning so I had to take it off and clean out all the hair that had gotten wound around it. I replaces it and now it is make a lound noise, but only when the brush is on. Could it be the belt making such a loud sound? It wasn't making this noise before.

Could very well be the belt.\015\012When cleaning the brush it is a good idea to add some WD40 at the ends where the plastic pieces are that hold the brush in the vacuum. The brush needs to be able to move freely around the plastic pieces.\015\012Ad ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Sebo X4 is squealing when pulled back. Takes a while after it's been running for this to happen. We changed the roller brush (needed it anyway) but didn't take care of the noise. Could the wheels be making this sound? At least that's what my staff thinks is going on... I own a commercial cleaning company and all we use are sebos... they're an amazing machine!

Yep - we think Sebos are pretty good too. I work at a Sebo sales and repair dealership! The wheels are a good bet - I can't think of anything else that might cause the noise. If in doubt, I suppose you could simply wheel one around for a while when s ... Sebo X4 Bagged Upright Vacuum

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis

Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Eureka boss pro 20... I need to take it apart

... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

Need to take off roller belt on my Eureka 4700D3

... Eureka Maxima 4700 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0812 seconds