Having problems with your Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum ?

Behind the brushs, there appears to be a plastic part (tube) that is broken. Is this common and/or easily repaired?"


Answers :

The tube you see, is just the underside of your height adjustment knob. It may look jagged, but it is not broken.
Repair Help & Product Troubleshooting for Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Behind the brushs, there appears to be a plastic part (tube) that is broken. Is this common and/or easily repaired?"


The tube you see, is just the underside of your height adjustment knob. It may look jagged, but it is not broken. ... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode


... Hoover Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

S 380- power 1800 is my Miele vacuum cleaner which I purchased in May 2009. A big hole has appeared in the tube. Can I cut part of the tube and fix it? if not where can I buy a new one? I looked up spare parts company but they dont tell me if the sise is correct


Miele vacuum hoses can be found athttp://www.totalvac.com/mielehose.html ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brushes will not spin -- broken part


Did deeper, I finally just fixed mine today, I thought the same thing about it not wanting to come apart, but try one more time, and when your almost done, look underneath there is a long plastic piece with two screws almost side by side towards the ... Hoover F7222-900 SteamVac Upright Vacuum

I have a roomba 530 pet series. It appears that the brushes aren't turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn't get pushed into the bin.


The belt either broke or has come off the track.... this should be easily accessable from the underside of vaccuum ... iRobot Vacuums

Middle Brush the middle brush just falls out. Doesn't appear to be broken but it still just comes out very easy.


You will have to replace the brush block ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Please tell me why I should consider buying a dyson after 4 years mine has had to have new parts and now it is totally beyond fixing. So many parts have broken off of it and I can only use so much duct tape to repair. I need a new vacuum but I am very skeptical to invest again in a dyson.


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

A small thin antenna cord on my radio got sucked up, and I immediately turned my vacuum off and easily puled out the small cord, Afterward the brush on the vacuu would notrotate.. The belt is not broken on the vacuum is not broken. My husband cannot figure out what the problem is


Hi Susan. There may still be a piece of the cord in the brush roller bearing. Check the ends of the brush and have a look. If its clear the belt is probably strethed. An easy way to test this is to turn on machine a put you hand against brush, if it ... Riccar 8955 Upright Vacuum

I have a Euro-Pro Shark Cordless Sweeper Model UV610. The motor still runs but the spinning brushes are no longer spinning. Can someone that is familiar with this appliance please assist me at repairing it and/or what parts I may need for repairing it? Thanks T.R.


IT SOUNDS LIKE YOU HAVE A BROKEN BELT, THAT CONNECTS THE MOTOR TO THE ROTOR BRUSH. ... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

There is a blockage occuring at the first bend right above the roller brush.It appears to be caused by a broken piece of white tubing within the black tube/


Hi Vstanle,you have diagnosed it correctly, the best solution to your issue is to have the part replaced which is available from the link below. ... Oreck XL2200 Bagged Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]


You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

I get plenty of suction at the hose, and none at the brushes. Also, the vacuum will not remain upright when I push it up. It appears that the part that switches the suction from the hose to the brush area is not engaged.


I looked up the problem where the machine would not stand upright, used that solution, and it worked. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this


... Vacuums

The repair shop told me my Oxygen3 needs to have a sumo(?) board replaced...again. I am not willing to pay for another repair and am wondering whether an new hose and adjustable extension tube would solve the recurring problem. Is the sumo board located in those parts or is it a malfunction that transfers to somewhere in the canister?


The Sumo Board, is housed inside the canister section, part # and discription below\015\012E-1180136-56 SUMO BOARD\015\012So replacing the hose and or wand will not fix the problem. Suggest you stay away from "big box", retail, discount s ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0669 seconds