Having problems with your Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum ?

How do I change the belt on Eureka The Boss model 5856?


Answers :

Repair Help & Product Troubleshooting for Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I change belt for Eureka Whirlwind Lite "Boss" model 450 A


Remove the 4 screws on the yellow top of the vacuum. The yellow plate will pop up exposing the belt and roller. ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

How do I change the belt on Eureka The Boss model 5856?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Eureka altima model 2993 how to change belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help


You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

Eureka Boss 12 amp Belt change - Eureka Mega Boss 4460DT Vacuum


... Eureka Mega Boss 4460DT Vacuum

Changeing belt I have a Eureka Upright Limited Edition Model 4462D and can not for the life of me find my manual and can not find the screws to take off the plate to change my belt.....help!!!!!


On the top nozzle, there will usually is 2 screws holding the top done. There are slots or holes on each side near the front and the screws or in these holes. Remove them, remove the top cover and then you can get to the brush roll and belt. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

How to change the belt on a eureka vacuum model


... Eureka Smartvac 4870 Bagged Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

How to change belt 4870MZ Eureka Smart Boss Vacuum


... Vacuums

Change belt eoreka mega boss - Eureka Mega Boss 4460DT Vacuum


... Eureka Mega Boss 4460DT Vacuum

How to change belt on eureka vacuum 2996 - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The information you're looking for can be found on page 8 of the manual via this link: http://www.eureka.com/service/manuals/80244.pdf ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Change belt on eureka model 3271 - Eureka 3276AZ Pet Lover Bagless Upright Vacuum


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Belt change for eureka model 4773 - Eureka 2961AVZ Bagless Upright Vacuum


... Eureka 2961AVZ Bagless Upright Vacuum

Belt how do i change the belt on the bagless eureka boss widetrack?


There are a total of 6 screws - one is hidden under the right front wheel. pull the wheel assembly against its spring - it's under there. ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

How to change belt in eureka altima vacuum - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Here is the belt you need to replace and the manual which has instructions:Eureka Altima Belts ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My Eureka The boss Smartvac Model #4870 roller brush won't turn even on the highest setting and the belt smells hot. we took the belt off. How can you tell if it needs replaced?


Just by what you explained I can tell that it needs to be replaced. The belt doesn't have to be broken to need replacing, if it is stretched and worn then it will slip on the motor shaft and not turn the brush roll and get hot. Here is a link to the ... Eureka Smartvac 4870 Bagged Upright Vacuum

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this


If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

How to change on belt on eureka model # 2991 - Eureka 2991AVZ Bagless Upright Cyclonic Vacuum


Here is the belt you need and a manual you can view which has instructioins:Eureka 2991AVZ Belt ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

I HAVE A EUREKA ALTIMA AND CANT CHANGE BELT - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The hood will come off if you loosen two screws at the front on top of the hood by the brush bar bit that is slightly raised. Then there's a screw to the left hand side of the upright either below the hose or duster area. Once all screws are undone, ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Belt?! hello, I need to change the Eureka Oxygen Canister Air Driven Upholstery Tool's Belt (model 5860Avh), but I don't know which one to get? any help please? Best, Pierre.


You will probably have to order it online. ... Vacuums

Change vacuum, clearner belt on eureka the boxx model 2271 type a


... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0605 seconds