Having problems with your Eureka 5860A Bagless Upright Cyclonic Vacuum ?

Bad beater bar end bushing for eureka 5860--part number??

Answers :

Repair Help & Product Troubleshooting for Eureka 5860A Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bad beater bar end bushing for eureka 5860--part number??

... Eureka 5860A Bagless Upright Cyclonic Vacuum

I have the eureka boss 4495 widetrack and the end piece of the beater bar broke off. I guess I put it back together wrong when I put a new belt on. Where can I get a replacement part and will it work do you think.

Call the Eureka people (1-800-282-2886) and describe to them what the beater bar thingy that you broke is. Ask them if you can order that unit--if you think you can install it. Otherwise, ask them where to the authorized repair person closest to yo ... Eureka 4495A Bagless Upright Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the

Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??

This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.

The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

What do the numbers on the Kirby G5 beater bar end caps mean?

The numbers on the beater bar end caps are used to lower the brush down as the bristles wear down. When you bought the machine, the brush roller started in the 1 setting. One year later, after the bristles have worn down, you can move the numbers ... Kirby Ultimate G Bagged Upright Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.

... Panasonic MC-V7515 Bagged Upright Vacuum

On several occasions the belt has come off the Hoover Windtunnel beater shaft and had to be re-installed. Is there any way to prevent it from slipping off? The shaft seems to be made so that the middle if it is wider(thicker than either the end or the part closer to the motor, which, to me, is a bad design so I don't know how to overcome this problem. I'd be very grateful for a permanent solution to this problem. Thanks in Advance, mas

Your belt is stretched and needs replacement ( # 38528035 ) . The agitator is crowned so that the belt stays centered. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?

... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss

Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

I have a Germ Guardian GGU350TT. The Beater Bar Brush is seized up on the ends and no longer rotates. Can it be fixed or can I buy a replacement Beater Bar Brush? I've called the company and they were no help.

... Germ Guardian GGU300 Bagless Vacuum

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane

... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Need replacement bushing part number for Kenmore, or motor?

... Kenmore Vacuums

We are unable to find a replacement part that the filter attaches to in the dirt cup on our Eureka Boss Pro Model 411. This part seals the top of the dirt cup and holds the filter in place. What is the part name or model number for the replacement?

I just called Eureka (1-800-282-2886) and asked for the dust cover lid. It was part number 61538-1. They said they could ship it to me or I could call one of the authorized service centers nearby to see if they had one. I wasn't in a hurry and the ... Eureka 411A Upright Vacuum

I need a service manual for an Electrolux C104A vaccuum. I know the part I need but don't have a part number. The part description is the hose connector at the beater attachment.

If you talking about the part that swivels it is called the elbow and the part number is 46861. ... Electrolux Guardian Bagged Canister Vacuum

Bissell 6579-2 bagless vacuum. Beater bar siezed up. motor turns. took bar out, no movement from either end cap on bar.

1. Uing the appropriate sized drift punch, tap out the steel axle rod which passes through the beater drum.2. Each end cap houses a 608ZZ ball brg.3. Check each brg for freedom of smooth rotation. Replace both if either is seized. ... Vacuums

When replacing the beater bar on the Oreck XL upright with a new bar, what way do the words "new" and "old" on the ends of the bar face?

Hello,I don't really understand your question, but I believe you are trying to replace the beater bar of your Oreck XL.... Follow the below instructions on how to replace your vacuum's beater bar:Turn your upright vacuum clean ... Vacuums

Part numbers for washers and end caps of vacuum agitator brush

The part numbers for the washers and caps can only be found if you know the agitator brush number.  ... Panasonic MC-V5745 Bagged Upright Vacuum

Need part for electrolux beater bar rug cleaner.

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0831 seconds