Having problems with your Eureka 5892AVZ Bagless Upright Cyclonic Vacuum ?

Motor is noisy like there is something stuck in it. I am looking for the service manual so I can see how to take it apart/

Answers :

Hi\015\012Generally modern upright vacs don't have screws that you can undo to get into the motor and most Electrolux/Eureka models have sealed units. I suggest looking at the sole plate where the roller brush is, check for anything clogging the main dust channel and then remove the hoses. Also take out the filters and give them a good clean, washing them are good but you must let them dry (or put in a low temp tumble dryer in a pillowcase with a towel) out. \015\012
\015\012You'd have to check out Eureka's customer services for an imploded service manual. Check on their website if nothing else works.
Repair Help & Product Troubleshooting for Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor is noisy like there is something stuck in it. I am looking for the service manual so I can see how to take it apart/

Hi\015\012Generally modern upright vacs don't have screws that you can undo to get into the motor and most Electrolux/Eureka models have sealed units. I suggest looking at the sole plate where the roller brush is, check for anything clogging the main ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

E series How did you take your rainbow e series apart? Do you have a manual? I've got a few pieces off mine but can't see where any other screws are to completly take apart to be able to look at motor. Thanks Kelly

The clear lenses on either side of the top part of the E-series Rainbow are removable. If you look at the each lens you will see two sections on the top edge of each lens that looks like this |___| |___| about 1 1/2 inches in from each end. Put a ... Rainbow E series Canister Wet/Dry Vacuum

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti

You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

Is it possible to take the Hoover Brush Block Assembly F7220-900 #48437029 apart so that I can thoroughly clean inside the block? It looks like it could, but I don't want to break it by trying.

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Can you take the Swivel Sweeper battery pack apart to replace the batteries with new rechargeable batteries? Batteries look like AA or AAA, but it appears that the battery pack is sealed. Is there any way to get it apart:?

Yes you can if you have a way to cut through the plastic outer case,(I used a Dremel rotary tool). Inside you will find six double A Ni-mh batteries. I found eight of these for sale on ebay for around ten bucks,then all you do is solder some wire to ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Changing belt How do I do that? It looks like I would have to take the screwdriver to the bottom and enter the engine compartment. I'm not sure that I feel confident to take this machine all apart and be able to get it back together again.

Its not the engine compatment take the screws out the cover 4 the roller will come off then u can c where the belt goes ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.

May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

HELLO I have an Oreck Orbiter Floor Machine, It makes a lot of noise. I seems like one of the side screws fell out. I did not see this happen. Nor did we see any loose hardware. My question is - How do I take it apart... to inspect inside. thanks SUsei

... Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum

No suction i have been using mine for like a year or so. today i went to use it and then no suction. the water comes out but it wont **** it up. I haven't had any problems till now. I cleaned the little red filter but still nothing. I dont wanna take it apart with out knowing what im looking for.

I had exactly the same problem with my five-year old my Bissell 7920, and it's probably a broken pump belt.  See page 19 of your instruction manual for how to replace.  The Bissel ProHeat belt accessory pack costs $3.99 and you get a pump b ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks

HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Torn Hose The hose on my Dyson is torn right at the top where the the accessories connect. I was able to take the connection apart and shorten the hose, but I don't know what to use to reattach the hose to the black fitting. It looks like it was glued...not sure what kind. Any ideas?

Duct tape ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I would like to know how to take my Kirby apart to service it without destroying it

Hello, kykyI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

DC28 Clutch DC 28 Clutch made knocking noise after about 1 hr of use. Tried to take it apart and see it it had an obstruction but burned up the belt and damaged clutch. Yes, I know I should heave taken to the dealer or warranty service but thought it was something simple. Nothing inside is simple on a Dyson! Can the clutch be replaced and from what vendor?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

I have a White Super Deluxe Sewing Machine, model 967. I am looking for a manual or if it cross references. Its only sewing backwards, and I see it takes cams. Thanks!

... Vacuums

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?

... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

My grundig yacht boy 400 has a broken antenna and I would like to repair it. It came off , has small screw still attached at bottom. Need to take apart radio and don't see how. Thank you, Lourdes

... Vacuums

I have an old kenmore canister 116-model 52612200 how do i change the belt i can't take apart the housing and have lost the service manual. any help would be awesome bg

I was unable to find a pdf manual that could be downloaded.\015\012I guess Sears wants money for the manuals.\015\012\015\012Call 1-800-366-7278 and tell them the model number and they will sell you a manual. ... Kenmore Vacuums

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara

... Vacuums

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.

... Electrolux Vacuums

I am looking for a service manual for a sunbeam AT35 toaster. Form searching around I believe that this is the same as a T35 Where can I download a service manual for this toaster

... Sunbeam Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0974 seconds