Having problems with your Eureka 5892AVZ Bagless Upright Cyclonic Vacuum ?

Vacuum doesn't go into carpet mode

\015 Hi, I have the boss 4d model vacuum and the brush isn't turning and it won't go into the carpet mode. I looked at the belt and it is on, but it isn't turning so I don't know what the problem could be. Please help.\015

Answers :

If the model number is 5892AVZ, either the brush roll is bad or the brush roll motor isn't coming on to drive the brush roll. There is a circuit breaker, make sure it didn't trip, reset it if it has.
Repair Help & Product Troubleshooting for Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Why doesnt my Dyson auto adjust on our carpet? We have a taller, soft carpet and it digs into it, making it very difficult to vacuum. We have had the vacuum for about a year at another house and it worked GREAT on the berber......our new has a tall carpet somewhat like shaved berber and now the vacuum wont work.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

Vacuum doesn't go into carpet mode


If the model number is 5892AVZ, either the brush roll is bad or the brush roll motor isn't coming on to drive the brush roll. There is a circuit breaker, make sure it didn't trip, reset it if it has. ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

When I vacuum the carpet it won't engage into the brush mode, or it does intermittenly. It stays in the brushless mode for the most part


This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem.\015\012\015\012I have finally fixed my sister's dyson dc 15 beater bar problem. It was just ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Eureka "The Boss" vacuum that doesnt seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.


I have a Eureka "The Boss" vacuum that doesn’t seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.\015\012 \015\012I woul ... Vacuums

My Kenmore model 116 vacuum head will roll in carpet mode but no suction, no action at all in floor mode.


Tripped overload, try resetting...Check pic.... ... Vacuums

Shark vacuum making loud noise when in carpet mode


... Shark Navigator Bagless Upright Vacuum

Dyson vacuum won't switch to carpet mode


... Dyson DC07 Bagless Upright Cyclonic Vacuum

The hose works great, but when I try to vacuum the carpet it doesnt work. The brush is turning, but I don't feel much suction. I checked for a clog and didn't see any.


You probably need the clutch replaced. This needs to be done every 1 to 2 years for most people ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

In Carpet mode brushes are not spinning. - Hoover U8135-900 / U8153-900 Savvy Turbo 7300 Bagless Upright Vacuum


Have you checked to see if it has a belt that drives the brush roller? If it has one it could have come off or broken. Also could be the control switch. ... Hoover U8135-900 / U8153-900 Savvy Turbo 7300 Bagless Upright Vacuum

Excessive noise Why does my vacuum #877 531 7321 116 36932503 make excessive noise when I use the suction tools on high. There does not appear to be any blockage. It sounds normal when I reduce to medium. The same noise happens when using carpet mode.


... Kenmore Vacuums

My dyson DC07 upright vacuum makes a loud noise when I turn on carpet mode. I removed he bottom plate and checked the belt and it looks ok


Did you check the roller brush to make sure it was clear of debris? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Belt not turning on carpet mode - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi, you say belt not turning on carpet does this mean the belt is turning if you tip the vac onto its back does the brushes then spin round as normal, if this is the case then this means that all you need toy do is get a replacement belt these can be ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

This unit tries to pump water but doesnt - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum


Go here for help > http://www.youtube.com/watch?v=SLyDeM10k9k ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.


You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

My dyson is stuck on bare floor mode. It makes it very difficult to vacuum carpets. Can I fix?


... Dyson DC14 Bagless Upright Cyclonic Vacuum

The vacuum works on carpet mode but not floor and only when the wand is attached to the floor brush otherwise it does not work at all


Please define "works" on carpet mode" do you mean when you say it does not work at all, that it does not run, or does not have suction. This sounds like the symptom of a clogged hose with blockage like this another vac needs to be used to draw ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

We are trying to fix our vacuum and we can not get the cover off to see what the problem is. The Carpet mode is not working and the motor is not running. Any advice? Thanks Katie


Hi, this could be many things. If I had more info. on the make and model it would help. It could be anything from a burnt out motor or a simple reset button. Whay happened when it stopped cold be valuable info. for me. Please gt back to m with the ma ... Electrolux Vacuums

Stripped gear noise occurs in carpet mode, not bare floor mode


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums


Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Difficulty to operate a vacuum cleaner on Smartstrand. I have a Miele which is a great vacuum cleaner. But it cannot move smoothly over this carpet. One's back is under stress trying to vacuum this carpet. The carpet is thick and luxurious and won't rot but it is hell to vacuum.


... Vacuums

Loud noise when I start the vacuum in carpet position


It's most likely the Belt Slip Protection Dyson uses to prevent the user from having to replace belts. I recently bought a Dyson and love it other than it literally sits there and makes horrible noises 80% of the time. I completely disassembled ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0901 seconds