Having problems with your Eureka 5892AVZ Bagless Upright Cyclonic Vacuum ?

Horrible sounds on carpet setting!

\015 My vacuum is working on the bare floor setting (but not that well), and has great suction with the hose. But! When I try to turn it on carpet setting, it starts making really terrible terrible sounds like something is hitting against something else inside the vacuum cleaner. I turned it on and looked in while it was running and the carpet roller wasn't spinning, it wasn't sucking, AND it was making the terrible sound. BUT I couldn't see what was hitting what. Suggestions?\015

Answers :

Sounds like what ours is doing. we took off the roller, and if you look on one side, it's melted. we're looking at either replacing the roller and seeing if that helps...and hoping it doesn't happen again...or we may just go out and replace the vacuum entirely. haven't decided.
There some screws from the bottom to remove then the top cover will come off, then you can check it over to see what the problem is.
Repair Help & Product Troubleshooting for Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Horrible sounds on carpet setting!

Sounds like what ours is doing. we took off the roller, and if you look on one side, it's melted. we're looking at either replacing the roller and seeing if that helps...and hoping it doesn't happen again...or we may just go out and replace the vac ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

My Dyson has suddenly starting making this LOUD, horrible sound when I am using it on the carpet setting. However, when I use it on the floor setting, I do not get this noise. Also, I think the 'sucking' power is not as strong.

You need to check the beater bar on the bottom and the hose from the beater to the canister. You may have something stuck in the beater system. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.

You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?

Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Does the epic 3500 have a belt? It seems that when running on the carpet setting, it is very noisy and is not picking up the way it should. When we run it on the floor setting, it sounds better, but the rolloer doesn't go around to fluff the carpet. What is wrong?

Yes, it does. It definitely sounds like a broken belt. And the noise would probably be due to the belt still being in the machine and hitting the motor shaft.\015\012Due to some difficulty in reassembling the powerhead and getting the belt to ... Electrolux Epic 3500 Vacuum

My brand new dyson dc33 vacuum ($399.00) is making an annoying sound when applied using a carpet setting. This only occurs on my thinner carpets, not on my thicker carpets. Do I have to inspect the clutch and fan mechanism and replace it? It's a brand new vaccum for god's sakes!

\015\012If there are no obstructions and it still makes the grinding noise here is something to try. When you take the bottom plate off which is real easy to do (3 plastic screws turn 1/4 turn with a coin) there is also on the bottom of the ... Vacuums

Nothing happens on the "bare floor" setting, it does something on the carpet setting but definitely not the normal sound or suction.

The switch frequently go bad on those. p# h-59136035 ... Hoover S2220 Flair Bagless Upright Vacuum

My Dyson DC 15 makes a horrible noise when switched to do carpets - sounds like gravel in the motor - and then comes the burning smell. Nothing keeping the brushes from moving, and I think they are. I am concerned that it is a belt or the motor. How do I know?

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Floormate Spinbrush The water comes out fine to clean but when I out it on the wet pickup setting, it piskc up in streaks and it has the most horrible sound while moving it around, like the rubber is going across the floor dry. Any solutions or anyone with similiar problems and a fix?

Not sure if this will help but these machines are ment to be used in one direction not back and forth like a vacuum cleaner. You should start in one spot and pull towards you slowly with the trigger depressed it is designed ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Older Dyson 07 Animal, loud ratcheting noise on carpet setting

That is an indication that the belts are worn, stretched or broken. You simply need to replace the belt. Here is a link to the belt(s) you need and a manual you can view: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.

I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?

Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda

Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Carpet setting: the brush drive does not work with the carpet setting. Is there a way to remove the bottom to determine if something is caught in the system?

To determine if you have a clog, first remove the attachment hose like you were going to put an attachment on. With the vacuum in the upright position, turn the vacuum on and place your hand over the hose. Do you feel a strong suction? If not remove ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I recently purchased this vacuum after reading consumer reports article on it and from recommendations from family. However, since I've had this vacuum it's been nothing but problems! I have a frieze carpet and I have the vacuum set on the highest setting. Each time I use it, the vacuum clogs with carpet fibers before I even finish a room! Any suggestions?

Is that a shag carpet? the power head is raised up all the way can you lower the suction on it is the carpet old the vacuum may not be able to handle the carpet,go to a vacuum store and see if you can try somthing else out some stores well let you re ... Hoover Tempo Widepath Upright Vacuum - Blue

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?

... Kirby Heritage II Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?

... Dyson "Stowaway" Canister Vacuum Vacuum

When i set it on carpet instead of bare floor it is hard to push when i vacume (when i turn nob it only has two settings floor and carpet no high pile or low pile)

Hi there,Sorry to hear you're having difficulties using your DC14 on this particular carpet. You may want to contact your carpet manufacturer to check it's suitable for cleaning with a vacuum cleaner equipped with a revolving brush. Manuf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Can you advise which setting should be used on different floors, ie hard floors and carpets, theres 2 different settings and I don't know which setting should be used on the different floors

Turn the machine on and look at the bottom. Turn to the two settings. The setting that stops the platten wheel from moving is for hard wood floors. If you cant tell, then setting 1 is most likely for carpets and 2 is for hard wood floors. Your ma ... Hoover Vacuums

Is it possible to adjust the head for a thinner carpet (right now it's on a setting that works for a thicker carpet, so it doesn't pick up anything on a thin carpet). Is it possible to adjust the head and if so how? Also, how do you wash the filter?

... Eureka 4700A Maxima Bagless Upright Vacuum

When i set the floor setting to carpet, it makes a nasty rattling noise. doesn't do it on bare floor setting

Hi,\015\012\015\012There is one major difference between the hard floor setting and the carpet setting - the brushbar doesn't spin on the hard floor setting. Hopefully this is a simple problem - the rattling noise suggests there may be so ... Dyson DC33 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5962 seconds