Having problems with your Eureka 5892AVZ Bagless Upright Cyclonic Vacuum ?
Brush spins & then trips & quits
\015 The brush spins, doesn't pick up much and then kicks off and I have to use the reset button on the side and it does it again. It doesn't pickup much, I think it must be plugged.\015
Sounds like a clog to me. Check that the roller brush cap fittings (caps at either end of the brush roll) don't have thread in them as well as checking that the dust channel from the sole plate is completely clear.
Repair Help & Product Troubleshooting for Eureka 5892AVZ Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Brush spins & then trips & quits
Sounds like a clog to me. Check that the roller brush cap fittings (caps at either end of the brush roll) don't have thread in them as well as checking that the dust channel from the sole plate is completely clear. ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum
I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge
Have a spin scrub a couple of years old. Have used it maybe 5-6 times and the green brushes only spin if you take the tanks off and set the machine upside down and push the brushes toward the machine... the second you stand the machine up they quit spinning.
Repace the belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
4296 Robotic Vacuum _ Brush quit spinning
I had the same prob. i contacted i-robot and was told the motor that turns the brush is shot. there is no replacement part. they offered to replace my i-robot with a new one from the 400 series. at about 60% of a new one. that's the only option that ... iRobot 4296 Robotic Vacuum
Bissell Pro 2X. The brushes spin as soon as I turn it on but only spins for an instant then it quits spinning. The vacuum stays running. the handle is down.
It might be the drive belt slipping if the unit is off then the belt is locked onto the belt and then when the unit is switched on the belt slips and if its loose it doesnt hold the belt to the motor shaft ... Bissell 9200 Upright Vacuum
Hoover Bagless Hello, My Hoover bag less (Model U5280-900) is not picking up dirt like it should. The brush roll is spinning fine, but the bristles on it are only about one quarter inch long. I am wondering how long they should be. The vacuum is quite a few years old. Do you think it is time to replace the brush roll. Could you email me at [email protected] about this topic. The product bar below did not contain my model no. The correct model no. is above in my message. Thanks
If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My Dyson DC28 works fine for a minute then it's like if the brush head gets too much resistance it quits spinning and the light starts flashing. When I turn the vacumn off then back on it's f
Hi Gayle,I'm sorry to hear you're having difficulties with your DC28. From what you've described, it sounds as if you may have the brushbar set at a level too low for the type of carpeting you're cleaning. If you select a higher carpet settin ... Dyson DC28 Animal Bagless Upright Vacuum
Hi, i have a hoover steam vac agilty. the brushes on the bottom front quit spinning. they are not locked up as i can freely turn them by fingers. is there a belt that i need to replace? if so, how do i get at it to replacec it? thank you for any assistance
The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum motor to spin a turbine and in turn spin the brushes. Most likely that path of air is clogged with hair or carpet fuzz. On the top of the machine there is a litt ... Hoover Vacuums
I have a steamvac/deluxe/spinscrub, model#F5862-900 the spin brushes quit working. is there a belt?
... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Brush roller quit spinning. - Euro-Pro V1828 Shark Stick Vac Bagless Vacuum
... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum
Roomba Discovery My Roomba Discovery seems to work fine, mechanically, but it no longer seems to collect any dust. (The collection bin remains empty after the Roomba has circulated around the floor for quite a while). The brush has been replaced and spins normally. Does anyone have an idea why this machine's vacuum function no longer seems to work? I would appreciate any feedback. Jeremy
Did you replace the filter? when you remove the dust bin there is a small filter that needs to be cleaned, or replaced. You can buy a maintenance kit that replaces the brushes and filters as well, its good to replace them all regularly ... Roomba Robotic Floor Bagless Vacuum
Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???
... Bissell 3130 Bagless Upright Vacuum
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate
If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums
MY WIFE BOUGHT THIS FOR ME FOR FATHERS DAY GIFT ABOUT ALMOST 2 YEARS NOW OR SO,BUT I HAVE THIS PROBLEM THAT THE BRUSH DOS'NT SPIN ANYMORE EVERYTIME I PUT THE SWITCH ON FOR BRUSH ON,THE HOSES BRUSH SPIN IS WORKING BUT FOR THE FLOOR CARPET BRUSH SPIN IS NOT WORKING,AND THIS IS THE MODEL NUMBER OF MY HOOVER VACUUM CARPET SHAMPOO CLEANER IT'S F7411-900
This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition
Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums
Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand
In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Brushes do not spin on my steam vac
We were having the same problem with the brushes not spinning. How I fixed it:I Removed the brush assembly by gently pulling on both sides of the assembly. I took a wide slotted screwdriver and inserted it into the slot (hole) that tur ... Hoover F7222-900 SteamVac Upright Vacuum
Brushes do not spin on my steam vac
Take the brush block out and see if the brushes turn of, if not replace the brush block. Otherwise it is the turbine(#23) that has to be replaced, sometimes you can take the turbine apart and clean it. The top cover has to come off, turn it over, t ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
Brush assembly will no longer spin on carpet however the suction from the system is still good. Unit is only 5 years old.
Probably a seized beater roller (the bearings wear out). Just order the new part and replace it and you'll be one your way again. And of course maybe a belt. ... Electrolux Centralux Vacuum
The brushes on my Hoover Steamvac Widepath LS SpinScrub model # F6040 900 are not spinning. What should I do to get the brushes spinning again?
On those models the brushes are turned by suction. 1. Check the lower tank to be sure its completely closed and sealed.2. Check the lower tank to be sure the tools filler plate is in place (if you used the tools recently)3. If both 1& ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The spinning brushes on the vaccum no longer spin, how can i fix this? The vaccum picked up a very small wire from a video game and i turned it off immediately. I unwound the wire but the brushes no longer spin.
You have either broken the belt or more likely the clutch easiest is to replace cleaner head assembly \302\24375ish or call Dyson and arrange a service if you're not DIY inclined but check belt !st ... Dyson Ball DC24 Bagless Upright Vacuum