Having problems with your Eureka 5893AVZ Bagless Upright Cyclonic Vacuum ?

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.

Answers :

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch after talking\015\012to several repair men. Talked to Eureka, too, and they were absolutely\015\012no help. Cheap wiring and switch made in China. Good luck trying to\015\012find a switch. vacuum-depot.com has switches, so you might try there,\015\012but make sure you get the 3-prong switch (same switch used on Eureka's\015\012Genesis). It is Part #27871.
I rewire with a thicker gauge wire from homedepot
Repair Help & Product Troubleshooting for Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Our dustbuster (dont' have model number with me-sorry) won't turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?

If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: ... Black & Decker 15.6 Volt DustBuster Vacuum

The female part of the catch which holds the lid to the accessories compartment closed has broken. This forms part of the handle to the vacuum cleaner.We've had the vacuum for less than a year but cant find the receipt so i think i will just have to pay for the parts. What is the part called that i need or the part number and where can i get it from. Many thanks

Even if you do not have the receipt you are still entitled to one or two year warranty.Since appliance sales are recorded after-sale by manufacturer, you need to contact the manufacturer to validate the warranty and get the replacement. ... Nilfisk Vacuums

Led lights, no steam. seems thermal switch is open. what is the temp of this switch? If a part number is available please let me know. Thanks Bob Howery

Hi,No part available...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Eu ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!

... Hoover Steamvac F5860-900 Vacuum

Power switch Can anyone provide a guide as to how to change the power switch (red up & down type) & the part number to buy a replacement, many thanks.

Here is a video that will give you full instructions how to replace switch ... Numatics Numatic Hhr200-2 Henry "Hound" Bagged Cylinder Vacuum Cleaner, 1200W

Need to purchase an on/off switch for my infinity nv31 but am having trouble finding one....the local vacuum store will not sell it to me unless I pay the 80 dollar fee to diagnose what I already know...I have already removed the part, but cannot find a part number nor supplier. I live in Pensacola. thanks

Is this some sort of special switch? Are you concerned with cosmetics? \015\012\015\012If not, Just find a spst switch, drill a hole next to the one where the old switch was and replace. Of course, make sure there is room for your 'new' ... Euro-Pro NV31 Infinity Vacuum

I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.

... Kenmore EVO All Surface Floor Cleaner Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.

... Kirby Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom

Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Eureka Boss 4D (5892BVZ) - Switch Replacement & Fried Wires

If you got the handle apart, Id say you can probably fix it yourself. You might be able to patch it but I would say to maximize your effortrs please visit RepairClinic.com to find the exact replacement parts you need. They also have expert advice ... Vacuums

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.

No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Hello, I am looking for a wiring diagram to install a touch/dimmer switch by "Comfort" mdl # RH-934B - Darjung Ind Ltd. It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire. The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow - no lampcord. Thank you very much for your help!

The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp ... Vacuums

I need the part that go's on to the steam handle for the other attchments to work. Let's see that's steam handle missing part then Other Attchments this is the only way I can name it, I hope you can understand what part I need. THANK'S

Hi,\015\012\015\012I have a better solution. Here is the parts diagram for the S3325. Please tell me which number relates to the part you need and I will find suppliers for you and the correct price. If your vacuum is not the S3325, pl ... Euro-Pro S3325 Handheld Steam Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Can you send me a La Cimbali M22 Premium espresso machine power switch wiring diagram? I have a machine without a power switch. The switch is on order but I still have to connect the 10 loose wires. Thanks, Terry...

... Vacuums

I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you

Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums

Where can I purchase a replacement wire for the handle of my aerus centralux hose? It's the black wire that runs from the switch in the handle and attaches to the pins in the wands.

Any Aerus Electrolux store should have them in stock.\015\012You can find the one nearest you by following the directions on the below site:\015\012\015\012 ... Electrolux Centralux Vacuum

I have 16981 Model. The trigger assenbly has snapped off the retaining pieces inside the handel. Can you buy a new handle with the trigger assenbly? What is price and part number? Also the lever to adjust the up and down movement of entire handle has broken. Can you buy? Is it possible to fix it and price for part?

The best place to obtain a replacement part for your unit is to either try and download an exploded view of the product, found in a service manual (which is often information restricted to the authorised repair agent), to get to the part number. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

S catch i have taken the top part of handle off, removed the screws under hose wrap, and layed the bottom part of handle down, i cannot find the s catch, can you tell me exactly where it is and what it looks like. i have looked all over this thing. thanks randy the model # is 8905

\015\012\015\012Just pull where I marked, it should come loose. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The foot pedal on my Kenmore upright vacuum cleaner has broken three times. The vacuum model number is 116.33923 and the Sear's part number is 8174906. Does Sears make this part in metal instead of plastic? It is becoming expensive to keep replacing this piece when it costs around $20 each time (including shipping) Thank you for your time. Jerry DeWulf

... Vacuums

Picked the zig cp3g at car boot sale,just what i was looking for,but no instructions just wires been cut,tidy little unit.on the battery transfer switch, red, green and blue. and from lights green,aux brown,and water pump yellow.....firstly how do i wire to power up,and how does the single wires from unit not have return wires,thanks.

Hi,\015\012\015\012For your requirement wiring will be following: the green wire will be from the knob beside\015\012the tree switch to battery switch. Red wire will be from another side of battery\015\012switch to circuit o ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0940 seconds