Having problems with your Eureka 5893AVZ Bagless Upright Cyclonic Vacuum ?

Every 3 swipes on the floor I have to push the reset button to engage the roller brush. Is this normal and if so why?


Answers :

No, it is not normal for the brushroll to stop that often. You may need to clear any thread, etc from the brushroll underneath the vacuum. Remove the screws from bottom of unit, stand unit upright, turn height adjustment dial to either side to allow hood to come off. Check the belt for any stress marks, stretching, etc. Replace the belt if necessary.
Repair Help & Product Troubleshooting for Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Every 3 swipes on the floor I have to push the reset button to engage the roller brush. Is this normal and if so why?


No, it is not normal for the brushroll to stop that often. You may need to clear any thread, etc from the brushroll underneath the vacuum. Remove the screws from bottom of unit, stand unit upright, turn height adjustment dial to either side to allow ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa


Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

I unscrewed the roller brush protective cover and removed the brush to clean it. Now the roller won't turn because the drive shaft is not turning. Is there a reset button or something?


I looked at the pictorial of this vacuum at this URL:\015\012http://middleeasten.bissell.com/images/UserGuides/3750.pdf\015\012\015\012This shows the belt to slide on the motor drive pulley and also on the brush. If the brush is bound up on th ... Bissell 3750 Lift Off Bagless Upright Vacuum

I have a Panasonic Performance plus MC-V5217. Something got stuck in the rollers and it stopped spinning. We've cleared the brushes but can't get it to spin. Is there a reset button?


... Vacuums

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have the Dyson Ball DC24. I can't get the roller brush to come on...what do I do? I have pushed the red button on the side of the roller but it still does not engage...


Hi its Darran at Dyson.The brush bar re-set switch would normally resolve this, however as you have tried that, please get in touch with our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US) so that we can help resolve this issue for you ... Dyson Ball DC24 Bagless Upright Vacuum

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.


Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Hoover tempo It will still **** through the hose but not from the brush-bottom. Can't find a reset button. Vacuum was GREAT and is only about three weeks old. I know it still works because it has plenty of strength through hose, but won't pick up when rolled across floor. thanks! Marian


Sounds like a blockage or belt off in the foot of the vacuum. there is no reset button on this model. ... Hoover Tempo Widepath Upright Vacuum - Blue

Hoover savvy reset button for brush roller - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

The roller on my Dyson DC24 quit rolling. I've taken out the brush, cleaned it, replaced it, locked it and push the reset button but it still isn't rolling. Help!!! I've only had this for about two months.


... Dyson Ball DC24 Bagless Upright Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.


... Eureka Vacuums

The brushroll on my dirt devil (vax X3) was caught o the curtain, and now the reset button will not reset the brush. the power comes on for the brush, but the brush will not rotate. What can i di to fix this problem


I didn't find the reset button until I took all the screws out and then couldn't separate it. Good luck! ... VAX Appliances Vax X3 Bagless Upright Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

Dyson dc25 off button won't turn off, brush button won't engage brushes


Hi ... did u get this fixed cos mine is the same hve to switch off on the wall? ... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson DC24 instructions say to push the red reset button for the roller bar. My vaccuum has no red reset button. Where is it?


... Dyson Ball DC24 Bagless Upright Vacuum

Dc25 brush button stuck on, cannot switch off, brush continuously rotates, reset button does absolutely nothing


... Dyson DC25 All Floors Bagless Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

While operating machine, brush does not rotate. Button is pushed in, all hair cleaned off brush. Is there a reset button? Where is it located?


Likely the wires are broken under the left hand cover not a difficult fix. Unplug the machine and remove the 4 torx screws and an access panel at the side of the ball. replace wires with new or re-connect with a splice. ensure wires are long enoug ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

A sound like a marble rattling around in the housing, when the roller brush is engaged. Roller brush and area clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brushes won't turn remain motionless as if cleaning hard floors even though button depressed could it be a problem with the brushes or button still under guarantee


There is a re-set button located on the brush head on the left side as viewed if you are standing directly behind the vacuum cleaner. It is black in color and is recessed slightly into the cover of the brush cover. It is round and about the size of t ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??


... Oreck XL Ultra Bagged Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?


Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0624 seconds