Having problems with your Eureka 955A Complete Clean Bagless Canister Vacuum Cleaner ?

Eureka Complete Clean 955A loss of suction

\015 Vac only 3 months old, used twice and now the suction at the bottom head is gone and the suction is weak in the hose. I took apart the bottom head and the duct were the dirt goes is clear, and the beater bar is clean with a new belt. I checked the hose and it's clear. The red filter light is on so I followed the directions in the manual and cleaned the filters and emptied the dust cup, that did not work either. The unit is starting to over heat also.\015

Answers :

Repair Help & Product Troubleshooting for Eureka 955A Complete Clean Bagless Canister Vacuum Cleaner

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka Complete Clean 955A loss of suction

... Eureka 955A Complete Clean Bagless Canister Vacuum Cleaner

My Bissell cleanview is NOT suctioning well, all filters, nozzles, attachements, canisters and belts are clean and in good repair. We've pretty much made sure everything that I can get to without completely dismantling the vacuum is super clean and/or new... still poor suction

Did u check the filter above the dirt cup?\015\012\015\012twist the yellow piece and wash the filter ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Eureka lightforce 300 poor suction, power paw doesn't spin and self cleaning duster doesn't clean its self when the button is depressed.

When this happens to me I do two things. The first is to empty the cannister but when you do (with the vacuum unplugged) stick your hand up inside of where the cannister goes.Sometimes that is filled with debris. Pull as much as you can out. There is ... Eureka 4718AVZ LightForce 300 Bagless Upright Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s

I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

My eureka vacuum won't suction and starts to smoke when I try to use it. It sounds like it is suctioning when I first turn it on, but after about 20 seconds it begins to smell like burning and does not suction at all. I have tried cleaning and unclogging the filter and everything. It's bagless so I don't need a new bag.

The problem is that your belt is stretched and worn. This causes that burning smell and it also causes the vacuum to not pick up well. You need to replace the belt. Here is the belt you need and the manual with instructions: ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Noticeable loss of suction, the filter has been cleaned

Your link doesn't work CHRISPURS1 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Suction loss when handle is tipped back to clean carpet

Ours did the same thing. I cleaned the filter and canister thoroughly. It needed to be cleaned, but that didn't fix the problem. I removed the plate under the carpet brush bar (three quarter-turn screws) and removed all hair, lint and threads from th ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi loss of suction on Dyson DC07 and I have changed the belt on the brushbar and cleaned all filters/removeable parts but still suction not very good, any other suggestions?

Check for a clog where the power nozzle connects to the hose. Clogs or leaks in the hose will both cause loss of suction/air flow. Another possibility is broken or worn out fan blades. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Hoover Windtunnel, 12-amp, UGG16-900 (or U6616-900 - hard to make out the "G"s from the "6"s) suddenly lost suction this morning. The dirt collection thing is completely clean (I always clean it out after using), the side filter is dirty but not destructively so, and I can see nor feel any obstructions in the hoses. Should I take it in (a real hassle in NYC) or get a new dyson? LOL.

Usually on this machine the door/valve assembly is to blame. if something gets caught in the door/valve assembly it can break this part. you can take it in to see what the est. would be. hope this helps ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Suction loss on bissel proheat 2x. will suction up water on bare floor but barely sucks up on rug. I have cleaned everything I can but just not doing the trick

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No suction, clean filters. - Eureka True Clean Upright Vacuum (Yellow) 2961BVZ

... Eureka True Clean Upright Vacuum (Yellow) 2961BVZ

Suction perfect when in upright position, but when tilted to actually clean there is total loss of suction - cannot see blockage anywhere. Thanks for your help.

If you are confident there are no blockages, look underneath, where the brush is, and you will see a short length of reinforced clear plastic hose. This often develops a split which results in loss of suction. You can pull the hose off at the motor e ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond

Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums

My Eureka/The Boss doesn't seem to have the suction power it had. However, when I place my hand under the hose, it has good suction, then when I try to pull in a small particle, it doesn't, unless I have the hose nozzle completely over the particle. The vac is 10 yrs. old. I cleaned everything. Someone said the belt. Would the belt matter if the hose doesn't **** well? It is just old and worn out? It did shut off recently do to overheating. Help. Thanks. Lorraine

Doesn't "The Boss" Vacuum have a filter? Perhaps your filter is clogged and not allowing it to work properly. ... Vacuums

Suction on my dc08 is very poor when turbine head is attached - no problem when not. I have cleaned the brushes an ensured there are no blockages. Why the loss of suction when using turbine head ?

Please go to the web page www.dyson.com and go next http://www.dyson.com/support/help.asp?article=1468&product=DC22-TURBINEHEAD-USand fix it. with commong sense.God bless you ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My eureka smartvac 4870 has no suction at hose or floor. all hoses are clear, filters clean and properly installed. bag not full and properly installed

Your eureka has no suction kuz the vacum hose needs cleaning ... Eureka Smartvac 4870 Bagged Upright Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

No suction cleaned everthing - Eureka 411A Upright Vacuum

... Eureka 411A Upright Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage

If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

I have a Eureka Altima vaccuum and it no longer suctions like it use to and also has a burning smell. I have cleaned all filters, brush, hoses, and filters. There are no blockages. I have also checked the belt and it's still good. Any other ideas as to what may be the problem?

This bagless model gets buildup of really fine dirt in the motor and starts to clog up the fan airducts. You will need to take the motor out and clean it. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hi when i use tools to clean stairs etc loss of suction have checked tube seems ok.........

First of all, are you using a extended piece on the hose? if so then you should feel around where the hose and extended piece are see if air is leaking ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Loss of suction after a burning smell - Eureka Whirlwind 4496 Bagless Upright Cyclonic Vacuum

The belt of the brush roller could of come off and could be causing the smell. Check the belt/brush roller ... Eureka Whirlwind 4496 Bagless Upright Cyclonic Vacuum

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??

... Eureka Capture Upright Vacuum Vacuum

Smells hot My Eureka Atlantis has been used for only my home cleaning use and today i went to use it and it is NOT suctioning like it should and it smells very hot and need assistance.

Sounds like you may have a bad motor. It is probably trying to work, that is why the suction is low and it gets warm. It will have to be replaced. ... Eureka Atlantis 2591A Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1793 seconds