Having problems with your Eureka Altima Upright Vacuum Model 2996AVS Vacuum ?

The plastic ends on the brush roller have melted.

\015 Eureka Altima Model#2996AVZ\015

Answers :

Bearings in the end of the beater bar have gotten dry/ dirty and created enough heat to melt the ends.
\015\012 I'm afraid you need a new beater bar.
Repair Help & Product Troubleshooting for Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

The plastic ends on the brush roller have melted.


Bearings in the end of the beater bar have gotten dry/ dirty and created enough heat to melt the ends.\015\012 I'm afraid you need a new beater bar. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have Eureka model 2961. The bearings on the end of the roller have seized and melted the plastic end. I was wondering if you know where I can find replacement bearings and a new plastic end cap.


Here are a couple of links:\015\012\015\012http://www.vacpartswarehouse.com/Products-p/62228-3.htm\015\012\015\012 ... Eureka 2961AVZ Bagless Upright Vacuum

Drive end of brush roller keeps heating up and melting the inside of the brush roller, this is a windsor expert carpet extractor


There brush bearings are seized. See the diagram HEREOn page 16, part numbers 14 and 19 need to be replaced ... Minuteman C45014-01 Self Contained Carpet Extractor Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.


Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Stuck Roller Same problem here. I think in our case, the accumulation of hair and the increasing resistance the hair created over time caused the hair to start melting, and eventually the end cap was stuck to the roller, which prevented the roller from turning. I cleaned out the melted hair(?) as best I could, but I think I need to order a new roller and end caps.


Befrore you plunk your $ down ...\015\012\015\012I dont now that you melted the hair so much as you may have an accululation of gunk and hair. If there is a good (not 'fast food' type) auto parts store near you, go there and ask the cou ... Electrolux 1910 Bagless Upright Vacuum

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers


The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

A cap on one end of the roller brush is centered and turns freely. The one on the other end is not centered and does not turn but does not look broken. It looks like it's supposed to be that way but it doesn't allow the roller brush to turn. How to I solve this?


It's hard to say definitively what the problem is here. Rollers usually have bearings at each end and they can wear or freeze up especially if they are exposed to water. When you say that the cap is not centered, I assume that you mean that you hav ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My dirt devil breeze was rattling while on. I found that the one end of the brush roller had shifted off the sqaure ends. Is it bent inside? Can it be repaired or do I need a new brush roller


The ends are fastened to each end of a shaft that passes through the roller. If the brush has shifted, perhaps the nuts or other fasteners have loosened. You can try to tighten the nuts but be carefaul to avoid tightening too much, causing the roller ... Dirt Devil Breeze Bagless VacuumVacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

The plastic drive for the roller brush on our dc25 animal is stripped out.it screws onto the motor shaft.does this part come with a replacement roller brush?


... Dyson DC25 All Floors Bagless Upright Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this


... Vacuums

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.


Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

How do you clean/take apart the roller brush ends. One end turns easily, but the belt end is somewhat harder to turn.


One end is usually fixed the other is not :pull staight out on the end with the belt. to put back :put on belt side first; lock in place with a little effort and put in other side. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>


I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need a new brush bar, The end (plastic) brokeand the brush wont roll!


You can try your local vacuum shop or look online at either eBay or amazon.com. There are also websites like govacuum.com or vacpartswarehouse.com Here is a link: ... Dyson Ball DC24 Bagless Upright Vacuum

I noticed the Roomba's brushes were not sweeping, or turning so they could sweep. There was a new sound coming from the machine, the sound of grinding nylon! Upon inspection, I determined the problem to be a heat melted gear support hole. The hole was no longer round but oblong. You could see a ridge of plastic around this hole. So melting I believe was the culprit. The gear that uses that hole was then able to tilt to one side, thereby allowing the gear to disengage from the drive train. I


Be sure to keep your brush bearings clean. If they get clogged, the brushes don't turn and the drive sockets can get damaged. ... Vacuums

How can I change the belt on the kirby vacuum shampooer brush roller. There is no way to snap the roller out and it seems that trying to unscrew the end isn't doing anything either.Model 5584 renovation group is what is written on the shampooer attachment. The kirby is a heritage model 2HD - purchased in the late 1980's.


... Kirby G6 Bagged Upright Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The roller that spins with little brushes stopped suddenly and no longer spins. I pressed the red little knob at the end of the roller but it doesn't fix the problem.


Open up the roller area check to see if somthing got picked up and jammed into the rollers so that it can't work, a rock or a screw or you might even have a large amount of string or fibers wrapped around the shaft or brush keeping it from rolling ... Dyson Ball DC24 Bagless Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0553 seconds