Having problems with your Eureka Altima Upright Vacuum Model 2996AVS Vacuum ?

My HEPA filter get's blown off of the vacuum when I vacuum. I just got all new filters and a new brush roll. Could something be clogging in the inside?

Answers :

There should be a cover that closes over the HEPA filter. If the cover is missing, or is there, but does not snap closed, then either snap it closed, or replace the cover.
If something was clogged inside, then the HEPA filter would be less prone to being blown off. But, it sounds like the filter or filter cover is not being correctly installed. The manual is not clear on whether the cover snaps closed.
Repair Help & Product Troubleshooting for Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My HEPA filter get's blown off of the vacuum when I vacuum. I just got all new filters and a new brush roll. Could something be clogging in the inside?

There should be a cover that closes over the HEPA filter. If the cover is missing, or is there, but does not snap closed, then either snap it closed, or replace the cover.If something was clogged inside, then the HEPA filter would be less prone ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hello, I have a Eureka 71b handheld vacuum. There is literally no suction. I checked the hose and it is NOT clogged. I thought it might be the filter so I bought a new filter. Still no filter. The rot

... Eureka Vacuums

My Model number 11635923502 kenmore vacuum is making a deep suctioning noise as if something is stuck in it. We have cleaned out the filters and all the vacuum lines thinking it was clogged. It is still making this noise and we are frustrated as to what could be causing this problem. The unit does not have much suction.

... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

The vacuum stopped working when i was vacuuming. The bag had a hole in it so all the dirt and stuff where clogging the filters. I cleaned them and put a new bag in but it will not turn back on. So I want to take it apart to see if there is more dirt on the inside,

... Fuller Brush FB-PT2 Vacuum

I have looked online for this vacuum but could not find it. The closest one is the Eureka 8803 but the p/n on mine says 79307. I have totally disassemble this vacuum. There are no clogs anywhere. Motor spins by turning shaft. Belt is new and turns brush. It still has absolutely no suction.

... Eureka Boss Capture 8803AVZ Bagless Upright Vacuum

One day I was vacuuming and it sounded like something went up inside somewhere and the motor, I assume,..... is frozen ..all it does is hum when I turn it on! I have changed the belt, filter and checked and cleaned all hoses... what could this be? THANK YOU, Gail

It's likely something got into the fan, is stuck there, is preventing the fan from turning, and so prevents the motor running. There's a good possibility the motor burned out because of this. If there's a strong smell of burning metal, this is prob ... Hoover Elite Rewind Bagless Upright VacuumVacuum

I have a cb9191j-10a vacuum that works fine but I am really disappointed by the small screw-on filter that quickly clogs up with dust and debris. There must be a larger type filter that could be used and this would make for a really fine vacuum. Could you suggest an alternative filter?

... Vacuums

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Bissell 37604 Bagless Upright Vacuum. Hose keeps clogging every time I vacuum. Is there a way to prevent this? I am ready to buy a new vacuum, but it does do a great job picking up hair...until it clogs. It clogs at top of hose. Could the hose be kinked? It does not look like it.

That is a defect in the design of that style of vacuum. I went back to my old vac because I got so tired of having to unstop it. The sharp turns in the hose and the molded plastic causes it. Find one without the turns. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo

Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.

You need to replace the belt. Replacement Vacuum Belts ... Vacuums

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?

Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush roll i am trying to find and purchase a new brush roll for my ge vacuum. The number on it says that it is 106585 and from what I can tell that is the same as 5550 parts. Is that correct?Thank you

I have the same vacuum for the last 5 years.  I dont know if its the same as 5550 (I assume it isn't) but I can give you the part number 61445-1.  It costs around $16 and you can call 1-877-207-0923 b/w 7 am and 8 pm Mon-Fri central time, o ... GE 106585 Upright Vacuum

Took my miele canister vacuum cleaner in for repair because the cord had a break in it creating a short. He said it also needed an inter filter ($12.29) and the carbon brushes were worn out ($21.95). Is that possible? Also wanted to service the motor and put in a new seal ($49.95) Shouldn't that include the inter filter and carbon brushes?

Depending on the age of the vacuum and how much use it gets, the first two are possible. I would question the brushes as they should last for several years.\015\012The servicing is generally for labor only and doesn't include parts. I do reco ... Miele Vacuums

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.

Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.

You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums

Kenmore progressive upright filter is being bypassed, clogging screen at outlet. Tried new filter, no change. 7 or 8 passes with the vacuum and the screen at outlet gets clogged.

Take the filter out and hold your hand over the filter connection. Turn it on and see where the air is being bypassed. What you see should suggest the fix. ... Kenmore 35622 Upright Vacuum

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano

... Electrolux Vacuums

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together

... Vacuums

Clogged Bissell After debris clears the brush part, it gets clogged at the point of entrance into the machine, barely anything makes it through the filter and into the canister. Clogs immediately after a few swipes of the carpet. Had vacuum for almost 3 years.

Something must be in the hose causing a clog, take the hose off and if suction is good where the hose hooks up, then there is something caught inside the hose. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1465 seconds