Having problems with your Eureka Altima Upright Vacuum Model 2996AVS Vacuum ?
Eureka Ultima we can get the cup off the base but the lid to emty it won't come off
Ok real easy grab the middle of the canister with other hand grab the top turn it counter clockwise it might be stiff but a little muscle should do the trick.
hope this helps
hope this helps
Repair Help & Product Troubleshooting for Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Eureka Ultima we can get the cup off the base but the lid to emty it won't come off
Ok real easy grab the middle of the canister with other hand grab the top turn it counter clockwise it might be stiff but a little muscle should do the trick. hope this helps ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
November 2008 I bought a Simac Stirella 9000D steam generator iron. Recently its been leaking water out the bottom of the regenerator. It makes a noise when it is trying to get the steam to the iron and it works then but afterwards when the noise stops it stops steaming and I find a puddle of water underneath the regenerator. Also a little steam comes out of the water tank at the top. I understand this is happening because of scale in the base unit. Can I get something to get rid of the scale? -
My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a
... Bissell ProHeat Deep Cleaner Upright Vacuum
My Kenwood steam mop sc5000 is no longer letting out steam. The lights are coming on, and the water is getting down to the base, but nothing comes out.
I'm having trouble getting the cup to remove. Once we did get it to come out and we put it back in. When we turned it on dust blew out of the vacuum where it should have been sucking in.
The dark gray plastic slide is separate from the Easy Empty Cup. Just slide the release tab all the way to open position, and then pull the Easy Empty Cup straight up.\012With a little effort, the cup will dislodge from the dark gray plastic platter. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
My steam mop gets hot but steam is not coming out when i pump it. However when I release the bottom attachment steam comes out of bottom of the base (purple part). I took the attachment off to see if it was plugged but dont see anything. Any suggestions?
Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
The lid on my sc-306 steam cleaner wont come off, is it pressurized
Press down and turn antyclockwise ... Vacuums
The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda
You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums
Manual I realize it's probably something simple but how do I release the Cyclonic Chamber on top of the Dust Cup lid? I see the red 'open to clean' release button but how do I get down in there to push the release button? Thank you in advance for your help! Best, Christy
Manual > http://www.sharkclean.com/manual/NV22-NV22C-NV22P-NV22T-NV22Q_REV_1008.pdf ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum
I was using my dyson dc25 when it shut off by its self. I was actually using the hose to get along my base boards. Now it wont turn back on. Ive checked for clogs and still 30min later its not on. What should I do know?
We have had our Shark for 2 years. It wont produce steam. We plug it in and the green light comes on. The tank gets luke warm to touch. But no more steam....
Hi,The heating element has gone bad.... 2 years is a long time for one of those things... from the volume of questions here many do not last nearly that long...\012Here is a tip that I wrote about the Euro-Pro Sha ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
It leaves dirt and fluff in the rollers not in the filter. So is not cleaning properly. There is never anf fluff at all in the filter. Also the lid does not close properly and we constantly get the 'check tank' light coming on. It leaves streaky marks across the floor and seems to leave the floor too wet (hence the streaks). Look forward to hearing from you.
Is there something stuck in the air passage between the tank and inlet ... iRobot 5800 Scooba Vacuum
Roomba wont stop going in circles,code 9 comes up, cleaned front caster wheel to no avail. 500 series roomba. called company said we need a new one, if this is the best we can get out of a roomba they are junk.
\015\012\015\012Your bump sensors are malfunctioning. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great.. ... iRobot Roomba 560 Robotic Vacuum
Red lid won't come off dirt cup
... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
I disconnected the Kirby vacuum to blow out and clean under my refrigrator, when I put it back it wont come on, don't seem to be getting any electric.
Make sure your electric plug is still in place ... Vacuums
Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative
Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums
Wand i can not get the wand out. It is suppose to be a quick draw it wont even budge i had 3 people pulling on it and still will not come out. help
I just took my DC17 apart to determine the problem (noted above). Basically it seems like there is a 'nub' on the lower part of the extension wand. Actually, there are two on either side, one higher (white, facing the back) than the other (black, fac ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis
Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums
I misplaced my manual for my sunbeam model 1128 warm mist humidifier and would like to know how to clean it....there is a white powdery stuff coming out of the base, how do i get rid of this....or could a manual on cleaning the product be sent to me....
The white powdery stuff is minerals, use a vinegar solution to warm water 1 part vinegar to 4 parts warm water. let it soak in the humidifier overnite or during the day and rinse with warm water. You could also use clr using bottle directions. ... Vacuums
Water wont come out when handle pressed to do floor or out of nozzle for upholstery cleaning smells hot when trying to get it to work could this be a belt
Yes it most likely is the belt ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Keurig b200 problem; When brewing with cup in unit water will pass into cup and it seems when k cup is full the grinds puch up through the top and water overflows. i pulled out the k cup holder and cleaned so their is nothing that is obstructed included the piercing pin. brewed [product does come through but does not seem to allow it to come through fast enough or if it supposed to be pressurized it is losing its seal on the top of the k cup
Have DC07 that won't come on. Wife said this started happening a few weeks ago. Would come on and then other times would not come on. Now will not come on at all. Believe I have a lose wire. Have taken off star screw by on off switch, but cannot find how to get plastic parts apart to get into electrical connections. How do I do this? I am sure I am missing something simple?
... Dyson DC07 Bagless Upright Cyclonic Vacuum
I can't get the vacuum to **** and can't get to the point of the clog. The pieces don't come off. Also need to know how to get the filter piece off the machine.
This link is for the manualhttp://www.dysonmedic.com/PDF%20docs/dyson_dc18_owners_manual.pdf ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
Euro pro mini steam zapper lid won't come off
... Euro-Pro Omega SC104 Steam Vacuum