Having problems with your Eureka Altima Upright Vacuum Model 2996AVS Vacuum ?

Eureka Altima - before I can get one room vacuumed the belt breaks. Why?


Answers :

If the belt is breaking that quickly, there is one very prominent culprit that could be causing the problem.\012Check to see that the beater brush, the roller brush that the belt is supposed to drive, is turning freely on the unit.\012Remove the brush and clean as best you can. Add some WD40 at both ends of the beater brush by the hard rubber holders and turn the brush by hand to work it into the joint.\012Reassemble and be sure the belt is put on so the brush turns in the proper direction.\012Paul
Repair Help & Product Troubleshooting for Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka Altima - before I can get one room vacuumed the belt breaks. Why?


If the belt is breaking that quickly, there is one very prominent culprit that could be causing the problem.\012Check to see that the beater brush, the roller brush that the belt is supposed to drive, is turning freely on the unit.\012Remove the brus ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?


That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Eureka TRUE HEPA Whirlwind Bagless same problem seems...roller just stopped...took everything apart and turned it on just in time to see belt melt...I was able to get the end caps off both sides at first and now can't seem to get the one side. Really love this vacuum! Don't want to have to part with it!


If you are able to remove one end cap, the brush roller shaft can be removed and the other bearing is exposed for examination and removal of the hair that probably is clogging it. After cleaning and reassembly the brush roller should rotate freely. C ... Eureka 2961AVZ Bagless Upright Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.


Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

I have a eureka vacuum model2996 type-DVZ i need a belt what one do i get.? thanks


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Eureka Altima vacuum. The model number is 2996. I don't think my vacumm is sucking any dust. Plus, it smells like a burning leather. What should I do? I have tried to get help from others and they tell me that I should change the belt. But, I don't know where it is. Please help.


Sounds like the belt for sure. Here is a link with the owners manual. It shows how to get to and change the belt. http://www.eureka.com/index.php?option=com_productdisplay&view=productdisplay&task=getproducts&productid=2&produ ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

How to change belt in eureka altima vacuum - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Here is the belt you need to replace and the manual which has instructions:Eureka Altima Belts ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I HAVE A EUREKA ALTIMA AND CANT CHANGE BELT - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The hood will come off if you loosen two screws at the front on top of the hood by the brush bar bit that is slightly raised. Then there's a screw to the left hand side of the upright either below the hose or duster area. Once all screws are undone, ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Eureka altima model 2993 how to change belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?


HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

How to change belt on eureka vacuum 2996 - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The information you're looking for can be found on page 8 of the manual via this link: http://www.eureka.com/service/manuals/80244.pdf ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I need to get a belt for my Eureka up right Model # 2271 what is the number of the belt and how can I get one?


Http://www.vacuumcleanershop.com/Eureka-Belts.htm?gclid=COSGj7qs05ICFQG5PAodmiJtlA ... Vacuums

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne


Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?


... Eureka Capture Upright Vacuum Vacuum

I need a replacement belt for a V1315 Shark Roadster Vacuum cleaner. Looks like there's no way to get one. Is there a compatible belt that will fit this vacuum?


... Euro-Pro Roadster V1315 Upright Vacuum

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean


... Panasonic Vacuums

Eureka Altima I have a Eureka Altima vacuum and can't get the dust cup out.


The dust cup has a small gray tray that appears to be part of the cup, but is not. I made the same mistake also and almost broke the stupid thing trying to get it out. Simply push the lock to the left to unlock. Gently lift the dust cup and not the g ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks


... Eureka Bravo II Bagged Upright Vacuum

I have a Eureka Maxima, this was a gift to me, but I have to say it is the worst vacuum I have ever used. Not only do I have a problem with the suction and the filter getting clogged, but it overheats - it takes me all day to vacuum my house, because the darn thing overheats after every room. Besides for tossing it off a cliff and buying a better vacuum, what can I do?


Get yourself a dyson ... Eureka Vacuums

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1409 seconds