Having problems with your Eureka Altima Upright Vacuum Model 2996AVS Vacuum ?

Cant figure out how to use the hose attachment,it connects at the top at the duster and at the floor,how do i change it to use the hose only?

Answers :

Repair Help & Product Troubleshooting for Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cant figure out how to use the hose attachment,it connects at the top at the duster and at the floor,how do i change it to use the hose only?

... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty

There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Torn Hose The hose on my Dyson is torn right at the top where the the accessories connect. I was able to take the connection apart and shorten the hose, but I don't know what to use to reattach the hose to the black fitting. It looks like it was glued...not sure what kind. Any ideas?

Duct tape ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I had used Dyson DC08 to **** out a wet car carpet. A few days later when using the V/C, there was a burning smell. Subsequently I washed the flexible hose, changed the pre-filter and post filter , but I wrongly put the pre-filter in the spot for the post filter. When the V/C was next used, there was again a burning smell and sparks. The filters were switched, but the V/C would not re-start. What shall I do?

Hi there,We'd strongly recommend against using your Dyson to pick up water. If you haven't already got in contact with us directly, I'd encourage you to do so. One of our experts will be happy to recommend the best course of action. You c ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!

Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm

I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o

Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have an elna 3007 machine. Our service man died and I need help with the tension. I can't get the top tension number to change off zero. when I free motion, all I get are loops top and bottom. I have adjusted the machine the best I can but still have the problem. I'm in the middle of a quilt and could use some help.

... Elna Vacuums

Cap (top) is froze. Unable to remove cap (top) to pour water inside for use. not sure if model specified is correct. It's a canister with hose and multiple attachments for cleaning.

I too can not figure out how to get the lid off. ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I have a Z345 Electrolux cylinder vacuum cleaner, from the 1970s probably, but not used much. I have lost the guide. I forgot to change the bag before it was full. Smoke started to come out - smelling of burnt paper, not rubber. So switched off. It did not blow the fuse, and may be OK. I wish to inspect it. How do I open it up? Alos I have an air filter and a motor filter for it. I have often changed the air filter on the top. How do I get at the motor filter, if there is one? Than

Good day! OK you have to is replaced the bag and that's it.And don't forget to change the bag again to avoid that problem.Thank you ... Electrolux Guardian Bagged Canister Vacuum

My new Kenmoore Powermate 116 canister has poor suction. I have no pets and light dust. Its not picking up small particles on the wood floor with the floor attachment. When I put my hand to the suction it feels weak. Cleared hose and changed bag. Using again, same issues. This should not be happening with a new vacuum. Is it a bad design in the elbow joint of the hose? I want to return this!!!!

First of all disassemble the handle and hose as much as possible and examine the inside. Make sure there is not any significant debris lodged in the hose somewhere like a plastic bag or something.\015\012\015\012Also check at the top of t ... Kenmore 23912 Progressive PowerMate Bagged Canister Vacuum

I have use my henry with no problem, tunred it off with the red switch on the top, 20 minutes later I went to use again but the machoine was toatlly dead with no power I have changed the plug fuse

Could be fault @ plug.. try cutting off 10 mm of cable then redo plug ..Replace fuse then try, if still dead try switch, you could short this out or if you have multimeter check for contact...if stii no action could be motor.... ... Vacuums

This vacuum is not picking up anymore when used as an upright, however it does still work very well when using the hose and attachments, I have looked at the vacuum but I cannot figure out where the clog could be.

Is the brush rotating?Have you turned it over, taken off the bottom plate and cleaned it out?Is the belt in good shape or does it no longer rotate the brush? Is it on the proper floor/carpet setting for the surface you are cleaning? ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Does the Hoover Elite 350 top-fill bag vacuum use hose attachments?

... Hoover Vacuums

Need instruction/care booklet for my Bissell powerforce vaccum model #3522-5. Bacfk of vaccum hose is filled with dirt and when attachment is used, dust & dirt fly everywhere. I don't have the care booklet for the vaccum and need to figure out how to fix the problem. Thanks

... Bissell 3522 PowerForce Bagged Upright Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?

Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

How do I change the outer bag clip? Can't figure out how to get the top apart to put in the new clip. The clip that goes to the handle.

I had a Kirby Classic and I had to slide off the clip.Don't rate me if this doesn't work. ... Kirby Generation 3 Bagged Upright Vacuum

Brushes don't turn. Don't know how to take bottom off. This is an almost new machine. Wonder if it has to do with the change in air flow from when you use the tube and then go back to regular. I feel like it is quite simple but can't figure it out. Thanks so much Judy

Hi Judy. If its new then I bet you its to do with the clutch. \015\012\015\012See the knob on the bottom of the machine. You use this to switch the Brushbar off and on. You can switch it off so that the brushbar wouldnt scratch a wooden f ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I am unable to get the handle off the top to use the hose. what to do?

Http://www.youtube.com/watch?v=Mm4rFq71zHA&feature=channelTake a look at this video ..at one point they show how to remove the hand ... Dyson Ball DC24 Bagless Upright Vacuum

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?

Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

I have a new electrolux el7025a-r and it keeps cutting off while I am vacuuming. I am using the small powerhead on hard floors and I have checked the hoses for blockages and the bag is new. I can not figure out why it keeps turning off in the middle of a job.

The wands are notorious for going out on that unit. One or both probably need to be replaced. Try to get it done under warranty if you still have the receipt, but they shouldn't cost you too much if you can't. \015\012\015\01 ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

I have a DC04 which is a number of years old and has started making an awful grinding sound, I'm sure it is the belt which I sprayed with WD40 and this helped for a couple of seconds but as soon as I recline the hoover it makes this noise but not when upright and using the hose. Does anyone have any ideas or how to change the belt? Thanks

You have to change the belt look it up with your local vacuum store. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0709 seconds