Having problems with your Eureka Altima Upright Vacuum Model 2996AVS Vacuum ?
Eureka whirlwind+ Is there a belt!? Smell hot like burning rubber...can't locate a belt to change?
It's a little tricky but here's how you get to the belt:
- Once you have removed the housing and the roller, turn the vacuum so that you are facing the pin the turns.
- Pull the belt to the back of the unit with your right hand so that the belt is against the pin on the front side and with your left foot apply pressure to the carriage where the roller sits. This action causes the plastic housing next to the pin to move toward the front of the vacuum providing enough space to slide the belt off easily.
- Be careful that you do not apply too much pressure with the foot.
Repair Help & Product Troubleshooting for Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Eureka whirlwind+ Is there a belt!? Smell hot like burning rubber...can't locate a belt to change?
It's a little tricky but here's how you get to the belt:Once you have removed the housing and the roller, turn the vacuum so that you are facing the pin the turns. Pull the belt to the back of the un ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?
... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Have eureka whirlwind + vacuum. Smells like burning rubber. Is there a belt to change?
Yes. You may have a bunch of hair or string that is binding the brush roller. CHeck that while you check the belt. ... Vacuums
I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?
... Eureka Capture Upright Vacuum Vacuum
Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this
If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum
I have a Hoover MAx Dual V carpert clearner and it is making a loud noise and smells like a belt is burning. Does it have a belt and if so, how do i change it.
Go here > http://hoover.com/search/?q=max+dual&x=14&y=3 click on your model and you can download the manual ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.
You need to replace the belt. Replacement Vacuum Belts ... Vacuums
Eureka 4870: when using hose, brush still spins, vacuum gets hot and smells like it's burning.
... Eureka Smartvac 4870 Bagged Upright Vacuum
I changed the belt on a Eureka WhirlWind superlite, all was well but I can't seem to find where this white piece of plastic approx.2" and less than 1/2" wide and there is a copper like V shaped clip, I was hoping maybe you's had a diagram or something showing where these go. Much Appreciated
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552328\015\012Generic problem for all Vacuums\015\012I changed the belt on\015\012Posted by hiphoppy69 on Apr 28 ... Vacuums
My vaccuum has lost suction. I changed the bag and cleaned everything out. The vaccuum is only 6 years old. I even replaced the belt around the brush. When I turn the vaccuum on it smells like burning rubber. My vaccuum is an upright 12 amp model #33000300C serial #Y347012385
... Kenmore Vacuums
I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.
Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums
We changed the belt and it smells like something is burning!
The new belt may be too big. Does it smell like burnt rubber? If so, then you need to get the correct size belt.Jim ... Eureka Vacuums
I have a Eureka Altima vacuum. The model number is 2996. I don't think my vacumm is sucking any dust. Plus, it smells like a burning leather. What should I do? I have tried to get help from others and they tell me that I should change the belt. But, I don't know where it is. Please help.
Sounds like the belt for sure. Here is a link with the owners manual. It shows how to get to and change the belt. http://www.eureka.com/index.php?option=com_productdisplay&view=productdisplay&task=getproducts&productid=2&produ ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??
... Oreck XL Ultra Bagged Upright Vacuum
I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?
... Kenmore 34722 Grab-N-Go Upright Vacuum
The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.
It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum
The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.
Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym
Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner
MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.
You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums
I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt
You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum
Eureka 2981bvz bagless belt pully is getting too hot and burning through belt
Check the brush roll, if one end has overheated and is locked up so it won't turn, then you need to replace the brush roll. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum
I am smelling a faint burning rubber smell and I think the belt needs changing, but I can't figure out how to open the case to change the belt. Can you help me?
... Hoover U5068-900 Sprint Upright Vacuum
Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n
From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums
I changed the belt on my vacuum,and the belt burned up,and snapped.Right after I changed it.Am I missing a piece??
Sometimes it can depend on the quality of the belt - if its brand new then it shouldn't snap the moment it is changed; if its an older belt sometimes they can break up the moment they're changed. Ensure that the model you have is correct with the cor ... Bissell Vacuums
Hello, I have the BISSELL PRO STEAMER MODEL 8805-1, it's mking rattling sound near the motor, & smells like melting rubber like when the belt is burning. I need check the belt, it's OK. Thanks so much, Susan
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum