Having problems with your Eureka Altima Upright Vacuum Model 2996AVS Vacuum ?

Eureka boss 5893A brush roll does not work

\015 I just got the vacuum and the brush roll was working and suddenly it quit but the belt is still ok. I have also used the reset button.\015

Answers :

You have to prss the pedal and lean it back the brush roll wil enguage
Repair Help & Product Troubleshooting for Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka boss 5893A brush roll does not work

You have to prss the pedal and lean it back the brush roll wil enguage ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Eureka the boss 5893A brush roller will not work

Is there anything jammed underneath.can you turn the brush roller by hand.if not then take it back where you bought it.sounds like you have a defective brush roller ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The brush roll on my Eureka Bagless The Boss 4 dimension cleaning vaccum itsn't working. How do I fix it?

Take either the plate over the brush roll off, if it doesn't come off, then the top cover comes off, should be 2 or 3 screws on the top to remove. Then you can get to the belt and brush roll. Check the brush roll, make sure the ends turn freely, if ... Eureka Vacuums

Eureka Boss height adjustment not working so brush stops turning

... Eureka Boss? SmartVac 4870MZ Bagged Upright Vacuum

How can i make my roll brush move on my eureka vacumn AS1101 A the belt is not broke so why wouldnt it work

... Vacuums

Eureka ez kleen brush roll not working? - Vacuums

... Vacuums

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.

... Eureka Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

The brush won't roll so i guess i need a new belt. the one there is intact but seems loose. Any other suggestions? Thx. Lynn eureka the Boss Model 405 and type B1.

... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

I have the Eureka The Boss Power PLus Model # 4703 Type A. When using the detached hose and wand it works OK; however, when using the Vacuum with the hose attached it doesn't work well at all.

... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha

You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Kenmore 35923 beltless brush not working after rolling up shlace.

Its due to the grip of the brush and the motor not getting fit its became little bit like streched so this happens and in this case replacing the brushes and checking any other component broken near to it is necessary. ... Kenmore 35912 / 35913 Progressive Upright Vacuum

ProForce 1500 has suction but the brush roll motor stops working.

... Proteam ProForce 1500 Bagged Upright Vacuum

Eureka model 71 how to clean the brush roll

... Eureka Vacuums

Eureka multicyclonic brush roll not spinning - Eureka 3276AZ Pet Lover Bagless Upright Vacuum

... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka Atlantis 2591A No suction...brushes working, soap dispenser working...

No suction means that the motor for the fan isn't working. You must dismantle it to access the motor and find out if it's powered. If it's not then you must check the connectors and the start button. If they are ok then the motor itself has failed. I ... Eureka Atlantis 2591A Upright Steam Vacuum

When i turn on my yellow Eureka upright everything works but when i flip the switch on the handal to do the carpet the brushed do not work. The belt looks fine. Is the motor dead?

The brush is worn out most likely ... Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

The roll brush will not turn when on floor. Too much pressure stops brush. Changed belts and still not working

Turn the belt inside out. This problem stems from a design flaw in the mechanism that turns the hoover from bare floor to carpet. After taking it apart I realized that the spring that pushes the belt tight (to make roller spin) is not any where nea ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis

Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0980 seconds