Having problems with your Eureka Atlantis 2591A Upright Steam Vacuum ?

How do i splice the power cord back together

\015 How do i splice the power cord back together after my dog chewed it in half.\015

Answers :

You will need to cut away the outer rubber insulation. Be careful not to cut the insulation on the 3 separate wires. Then you will need to remove about three fourths of a inch of insulation from each of the three wires. If you can solder, then solder the black to black, green to green , white to white. Then Tape with electrical tape each wire separately. Do a good job of taping. If you cannot solder, then go to a hardware store a buy # Wire Nuts. Take the loose end of the cord with you so as to get the right size of Wire Nut. The wire Nut repair is bulky , but secure. You are using a lot of Amps with the Steamer so you want a good job, lest the repair gets hot. Either repair I mentioned will work safely and well.
Good Luck !!!!!!!!!!!
Repair Help & Product Troubleshooting for Eureka Atlantis 2591A Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.

... Vacuums

How do i splice the power cord back together

Hi, You will need to cut away the outer rubber insulation. Be careful not to cut the insulation on the 3 separate wires. Then you will need to remove about three fourths of a inch of insulation from each of the three wires. If you can solder, t ... Eureka Atlantis 2591A Upright Steam Vacuum

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob

The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce

I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

After fixing the pull cord on the poulan pro ppb30 /30cc backpack blower i can not get the cord to pull back in if i pull it. how do i get the correct tension on the recoil spring when i put it back together?

... Vacuums

Can't get my Miele Power Brush SEB 236 Back together. Height adjustment mainly. Not sure where 1 loose spring goes either and which screws go where. Got it back together and had 3 left, then a 4th fell out when I vacuumed.

... Kenmore Vacuums

The mechanism that rolls back in the power cord seems to be working slower and sometimes not at all. Was wondering if the mechanism in question has an adjustment to increase the tension on it so the power cord goes in faster like it used to. Thanks Rafael

It easy to adjust the roll back of vacuums the problem is hard to dismantle the unit to remove all the things to see the adjustment roll,all vacuums is need to remove all screw to open the unit even to replace the small parts like switch,and sometime ... Kenmore Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

Problem with cord rewinding mechanism on my Nilfisk King!Whilst repairing broken cord(successfully)the metal coil thats part of that mechanism sprang out!Can someone out there tell me how to put it back together again PLEASE.I would so like my cord to be able to retract again

... Vacuums

My power cord will not retract back into the housing< i would like to open the back of the unit but there no screws or bults to due so. How do you open the back of model c151d

Try standing vacuum on end, then gently tugging and releasing cord. This generally will retract it.\015\012There are many problems that can result in disassembly and reassembly by an untrained person, including shock and fire. For those and o ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Power cord worn out where it enters motor, have to move cord certain direction and will turn on. Cord finally gave out one day and almost shocked me when it literally blew out. wont turn back on

You have popped the fuse in the plug top or have burnt out the wires in the cable \015\012\015\012No matter you have got to shorten and re-wire the cable into the cleaner or get a new lenght of flex and do the same thing.\015\012 ... Filter Queen Majestic Canister Vacuum

I can not get the power cord to go back into the canister.

If you can't get it to go back in by pulling on it, you will need to open up the machine to rewind it by hand. Open the front of the canister and remove the bag. As you are looking at the front of the unit, there are two vinyl coverd strips that run ... Electrolux Epic 6500 Vacuum

Cleaning and reassembling a Jarvis Walker Ultra Power 5500 reel and need help putting it back together. Are there any schematics for this reel online?

... Vacuums

I installed a new battery in my Roomba 540. It charges and runs directly with power cord but will not charge on dock. When I push the dock button, it acts like it "sees" the dock and approaches it and even slides on, but then gets back off again and just keeps going back and forth until I turn it off.

... Roomba Robotic Floor Bagless Vacuum

No power, were the power cord goes back into the unit. It started to shut off prior to quitting altogether.

Your cord conductor is broken in the area where it enters the machine ... Fantom Vacums Lighting Canister Vacuum

Power cord plug broke and cord went back inside.......how do i open??

Call your local Electrolux office. Trying to fix it yourself will void your warranty. If you need any assistance call 570-326-1731 and ask for Liz, I will be happy to assist you if I can. ... Electrolux Guardian Bagged Canister Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

How to put power nozzle back together e-series

... Rainbow E series Canister Wet/Dry Vacuum

S444i just would not switch on. When I took it apart I sprung the rewind coil on the cord retracter and I can't get it back together. Now I have 2 problems!! It won't start and the rewinder

... Miele Vacuums

The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?

You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger

There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums


Hi,\012Try to spred the pins slightly so that they hold the plug more tightly...otherwise the only thing to do is to try and buy a replacement cord...\012\012heatman101 ... Vacuums

Power cord won't retract back in - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Electrolux Genesis 1572F: 1) One of the two spring/clips/whatever that hold the upright upright for storage has busted. What is the part called? Where might I find a spare? Or should I go to a machine shop? 2) The power cord retainer thingy on the back of the handle grip has broken; any idea about part#, name of part, where to look? (I can't find a manual or whatever, exploded parts diagram, etc., online. I guess this is the planned obsolescence thing--after all, the machine is hardly even 2

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2048 seconds