Having problems with your Eureka Atlantis 2595A Upright Wet/Dry Vacuum ?

I am having those same problems , brushes are not agitating . leaking water from the bottom of the unit , the suction is week it is not pulling the water out of the carpet .

Answers :

Repair Help & Product Troubleshooting for Eureka Atlantis 2595A Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am having those same problems , brushes are not agitating . leaking water from the bottom of the unit , the suction is week it is not pulling the water out of the carpet .

... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

I have a Hoover Steamvac model #f5888-900. Recently, after finishing use, it leaks a lot of water from the bottom of the unit onto the recently cleaned carpets. Do you know what would cause this spewing of water after completion of use?

Either the rod in the handle is holding and not releasing the resevoir asm, this where the tank sits on, is bad. So water is not being shut off completely when off. ... Vacuums

Hoover steamvac when I use it it leaks out of bottom. when it off an water in tank leaks out of bottom,when its off an I pull the triggar it flows big time out of bottom. tank doesnt leak when off sitting with water in it

Let me start out with an apology. I did not ask my question very well - and you did not answer it as I needed.\015\012If you wish, we MAY be able to communicate in your native language. We can do most indian languages, Turkish, Ukranian and s ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Sorry I have water Leaking from the bottom of the brushes on my vax carpet washer the model is W90-RU-P rapide ultra 2

... Vacuums

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.

Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Eureka Atlantis carpet cleaner and a little water always leaks out of the bottom. Recently, the head of my handheld upholstery cleaner keeps leaking water. How do I get it to stop? Thanks.

... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

I have the Hoover max Extract 77 and when I'm cleaning the carpet, the clean water tank leaks on the floor, even if I'm not squeezing the trigger. The clean tank doesn't leak when I fill it, but once I place it where it fits and start using the vacuum, the clean water drains out on the floor. The dirty tank fills up, so the suction works, but, I don't know what is going on?

... Hoover Vacuums

November 2008 I bought a Simac Stirella 9000D steam generator iron. Recently its been leaking water out the bottom of the regenerator. It makes a noise when it is trying to get the steam to the iron and it works then but afterwards when the noise stops it stops steaming and I find a puddle of water underneath the regenerator. Also a little steam comes out of the water tank at the top. I understand this is happening because of scale in the base unit. Can I get something to get rid of the scale? -

... Vacuums

My Delonghi DSS50 steam floor cleaner water reservoir has a broken valve on the bottom where it fits into the steam unit. It leaks water rather than producing steam. I would like to find the valve and replace it or buy a new water reservoir with the valve in it. I cannot find the part I need. Can you help me?

... DeLonghi DSS50 Scopa Upright Steam Vacuum

NOTHING WORKS Used the unit 3 1/2 weeks ago, now it will not do anything except turn on. The water and shampoo will not dispense and the brushes will not turn. Is there some type of reset button that can be utilized????????? Have had unit for several years with only one other problem, the soap dispenser had to be replaced because it leaked. Teresa

Check the foam filter on the underside of the recovery tank lid, make sure that it has at least a 1/4 in. gap from the top. There also is a filter, from the bottom, it has a red frame, pull out far enough to clean it.\015\012On the bottom of t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My F7458-900 leaks water when using upholstery tools I do have good suction, but water comes out fast on the bottom of machine.

This sounds like the hose connection valve is bad. The part is about $12 -15. I would take it into a qualified repair shop for repair. This type of repair is worth it. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Using my hoover steam vac tonight and too much water coming out. once it's turned on, water and shampoo continuously come out underneath until tanks are empty. looks to be leaking from left side bottom as looking at it standing behind the unit

Make sure that you have filled everthing properly and the hoover steam is in a good condition. or check else is there any loose coonections in the bottom of the hoover, which makes the tank empty.if the problem persists take it to service. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

We have A "WC1000" 12 cup Coffee maker. It is leaking water out the bottom of the unit. We have removed the bottom metal plate, but there is nothing in that area requiring attention.

I think a gasket may have melted, or is leaking. Also check the ends of the little hoses. they may have cracked. ... Vacuums

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


Have a bissell pro steam cleaner the suction is great but the water leaks out the bottom I think it should spray from the front and the soap cleaner won't dispense from the bottle so I have to mix the soap cleaner in with the water Any solutions

Use this guide!\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No suction suction gate open. not pull water out of carpet

... Bissell Lift-Off Deep Cleaner 94Y2

I have a Kenmore Progressive Inteleclean Upright vacuum cleaner (with Bag) . It has good suction only through the hose now and none through the bottom for cleaning carpets. and, there is a noise like it has a suction leak. the brush is rotating.

Theres a little bendable neck that hose with suction plugs into. Thats the one thats clogged. You will have to fish it out by taking off the roller and clearing the clog. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the

Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet

Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

When I squeeze the trigger, water won't come out of my Bissell PROheat2X carpet cleaner. The beater bar rotaotes, and there seems to be suction. Nothing comes out the bottom.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water leaking out bottom with hose attached

The water hose plugs into the solution valve-pressure on the side of the noozle(bottom). There may be a water line that has come loose there, you will have to take the top off to get to it.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

Hoover F7458-900 Spin Scrub leaks water from bottom without pulling trigger when turned on.

The soap causes the valve in the trigger to stick u should be able to clean it by just using hot water and opening a closing the trigger. thank you josh ill be here for more info if that dont work ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Vax carpet washer deluxe leaks from bottom of water tank, somewhere between coming out of the tank and going into the jet to squirt on the floor. pissing me off - any help would be great!

Just stripped VAX rapid carpet cleaner model v-025 down found out the internal plastic water valve keeps sticking in open position causing the water to free flow on the carpet when it should be closed pop the water flow regulator part out of housing ... Vacuums

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?

The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction My quicksteamer does not pull the water from the floor in. It makes a funny noise and the brush is very loose on the bottom.

Bissell has made this model along with all of the older cleaners obsolete along with the parts for them. I would buy new. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1225 seconds