Having problems with your Eureka High Filtration s Mighty Mite Enviro Vac Vacuum ?

Brush stopped rotating and little suction on unit.


Answers :

Even though the brush is spinning, you probably need to replace the belt2_bing.gif\015\012because it is stretched. It is probably slipping on the beater bar..

Jim
Repair Help & Product Troubleshooting for Eureka High Filtration s Mighty Mite Enviro Vac Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush stopped rotating and little suction on unit.


Even though the brush is spinning, you probably need to replace the belt\015\012because ... Eureka High Filtration s Mighty Mite Enviro Vac Vacuum

My manual says it is DC07, but it is pink and silver in colour. I have 2 problems, firstly the brush has stopped spinning, but belt appears intact. Secondly there are tiny holes in suction pipe near brush i.e. the little section of suction pipe at base of vacuum cleaner.


Hi there, \015\012The DC07 came out in a few different variations so the colour only indicates that yours has a hepa filter. The first problem can be caused by a few different things\015\0121. the brush roller bearings are worn or siexed. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Very little suction from vacuum is occurring after I pulled a string from the roller. Hot air is blowing out of unit. Was working fine until I pulled out a string...Suction is occurring from wand.The brushes now make a loud sound too when activated...do I have to take the unit apart to readjust them or something?


Yes re adjust ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

NO SUCTION HOOVER U8143-900 UPRIGHT HAS LITTLE SUCTION ALL BRUSHES ROTATE SO I'M SURE THE BELT IS OKAY. DO YOU ANY SUGGESTIONS????


I took mine apart, cleaned otherwise inaccessible pipes, and assembled\015\012it back (that went well, huh!). The clog was made of human hair and and\015\012other long fibers (carpet pieces, etc). ... Hoover U8143-900 Upright Vacuum

I have hoover mdl U6459-900 and the brush will not rotate even though the main pulley belt is rotating. i have changed booh belts and this did not solve the problem. the suction on the unit seems ok. thanks??


Sound like you need tear down and find whats jamed in it to stop it from turning like string ore hair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I accidentally sucked up a string. The brushes stopped rotating and the suction was low. I took the frame off the brushes, and the rubber belt came out. How do I re-attach the belt/fix this problem? It is a Bissell power force turbo upright.


You'll need to replace the belt. \015\012On uprights with rubber belts, the belts need to be replaced every 3-6 months due to the fact that since the belts are rubber, they stretch, and once they stretch out they decrease the rotational speed o ... Bissell Vacuums

No suction The brushes spin as normal but there is little to no suction through the base of the unit.


Your Belt band probally broke. My is doing the same thing, I wonder if I could sew the belt back together? ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a one year old Beam central vac. It has supervalves. The handle (connected to the hose stopped turning on the unit. The handle still powers the brush but no longer turns on the suction?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566201 ... Vacuums

116 31811010 Vaccum motor stopped working during use. It's getting power, lights and brush rotation, but no suction.


... Vacuums

I havethe first generation purple Dyson Animal model. The brush rotates fine, but doesn't make sufficient contact with the floor/carpet, therefore does not pick up most items on carpets (suction still works however). If I put my foot on it and push down a little, it works. However, since I'm not an accomplished acrobat, this is not easy to do. :-) Any suggestions on whether this is fixable? Or should I just save up to buy a new one?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brushes and the belt are not rotating. The power seems fine and there is suction. I have no other history on this problem since I was given this almost new unit over Thanksgiving. Where should I be looking for a problem/solution.


If you've got suction, but the brushes and belt are not rotating, then either the belt has come off the motor shaft, or the belt is broken and just looks OK.Remove the bottom cover off the floor head and check that the brush roller turns ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for


Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look


... Kenmore Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?


As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.


Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Hi. I have a DC 24 which when brush rotates makes a very loud noise. I have replaced the brush and side bar. The side bar appears very loose. The noise stops when I switch the brush rotation off. Any ideas ?


Hi there,I'm sorry to hear you're having difficulties with your DC24. If the cleaner head seems to be making an unusual noise during use, you may want to check all the parts are correctly assembled, and that the cleaner head and brushbar are ... Dyson Ball DC24 Bagless Upright Vacuum

My roomba 560 has brushes that spin one rotation then stop then you hear a click and they rotate one rotation stop over and over. I took compleatly appart cleaned, lubed, and inspected all looked good?


Here's the solution to this problem...\015\012\015\012Remove the rollers and run the Roomba and see if the problem goes away. If so, here is the solution to the problem...\015\012\015\012Each roller has a little yellow cap on ... iRobot Roomba 560 Robotic Vacuum

My rotating brushes have stopped rotating


Almost certainly you have broken a drive belt. It is not a big deal though just turn it upside down and remove the base plate you should be able to access the belt from there. You should be able to get a belt pretty easy from an online retailer like ... VAX Appliances Vacuums

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0627 seconds