Having problems with your Eureka optima 431f ?

Where to get belt and how to change

Where to get and how to change the belt on an eureka optima 431f yellow

Answers :

Repair Help & Product Troubleshooting for Eureka optima 431f

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Change belt How do I change the belt. I took the bottom off and removed the roller but can't get the rest apart to get to the place to hook the belt on the the drive.


... Hoover U4270-930 Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.


Model no. req ... Hoover Vacuums

How do I change the belt on the side. Have a Bissell Power Lifter. The belt broke and i cannot get it changed. HOW do I change it?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Change belt How do I open the power head to get to the belt to change it?


... Beam Rugmaster Plus Belt

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Belt the belt on my dc 14 will not turn does that mean i need a new belt and how do i get it changed


Hi.Your Dyson will probably have A clutch unit this engages the brush roller when you pull the handle back to vacuum.Check the clutch control knob which is at the bottom left front side of machine looking from the front & ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Changing a belt on a Hoover Vacuum Cleaner, Model U4264-930. can not get the old belt off.. U4264-930can not remover old belt on sweeper


... Hoover Vacuums

How do I change a belt on a Dyson. I can't get


Watch this dyson replacement\015\012\015\012hope it helps ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do you change belt. I have cover off, but can't get brush off


Http://www.bissell.com/images/UserGuides/3574-3576_1005.pdf ... Bissell 3576 CleanView II Bagless Upright Vacuum

I have a Dyson DC33 bagless vacuum and the beater brush is not turning .. How do I get the cover off the brush to change the belt?


If you lay it down so you can see the bottom of the vacuum, there should be 3 flathead looking screws,just turn them a quarter turn or so, and that bottom should pop off so you can take the brush out and change the belt, just make sure you watch how ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Change the belt in my kenmore power-mate 120 amps...how to open it to get to where the belt is???


HELLO, JUST REPLACED THE BELT ON OUR'S. FIRST TAKE LITE LENSE OFF THERE WILL BE 2 SCREWS, REMOVE. THEN FLIP OVER POWER MITEON EACH SIDE PRY WITH 2 SCREW DRIVERS WHERE THE ARROWS ARE TO SEPERATE & THERE IT IS THE BELT. MIKE ... Kenmore 23313 Whispertone Bagged Canister Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Need to change belt on hoover upright model u5093-900, but can't figure out how to open it up to get at the belt.


... Hoover Vacuums

Impossible to change belt--cannot get belt to go over pulley.


First put belt on big round roller then use a flat screw driver to pull it onto the motor shaft ... Panasonic MC-V7515 Bagged Upright Vacuum

The roller has stopped rotating and I wanted to see if the belt needs changing. I cannot find out how to get to where the old belt is located.


Remove the bottom to find the belt. There is usually a spare in the compartment. I think there is 8 or 10 screws.\015\012\015\012Thanks for your interest in FixYa.com\015\012 ... Oreck XL21 Bagged Upright Vacuum

I have a kenmore vacuum cleaner that I bought a new belt for butcannot get the bottom off to change the belt. Model # 116 53312305


... Kenmore Vacuums

I am trying to change the belt on a hoover legacy dirt finder. I cannot figure out how to get to the inside pully where the belt hooks


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=733898\015\012Generic problem for all Vacuums\015\012I am trying to change\015\012Posted by fuzzyplus1 ... Vacuums

Change belt how do I get to the belt, it is off will not turn


Turn the vacuum upside down so you can see the bottom of the head (the part that comes in contact with the floor). There are screws that need to be removed so the plate can be taken off, remove those screws. Now the brush is accessible, lift the brus ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

I cannot find how to get bottm plate off to replace sweeper belt. where do you change the belt?


There are 3 screws on the top housing, one on the front Right, Front Left and behind the hose in the back ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Change belts I have all the screws out and I still can't see how to replace the belts. Any ideas how to get the cover off? Thank you


The hooverstore page is down...schematic is here:http://www.vacsrus.com/CartGenie/pg_U8146900.asp ... Hoover U8143-900 Upright Vacuum

Belt?! hello, I need to change the Eureka Oxygen Canister Air Driven Upholstery Tool's Belt (model 5860Avh), but I don't know which one to get? any help please? Best, Pierre.


You will probably have to order it online. ... Vacuums

Change belt How do I get at the roller to preplace belt


To get to the brush roll, you have to take the bottom part. There is no belt, the brush roll motor is part of the brush roll. ... Panasonic MC-E583 Bagged Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0797 seconds