Having problems with your eureka powerline mighty mite ii model 3641 ?
how do I repair this vacuum
While using vacuum it just stopped running.
Repair Help & Product Troubleshooting for eureka powerline mighty mite ii model 3641
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hello, I have an Electrolux vacuum. In desperation, I vacuumed up some water and my machine stopped. I am hesitant to take the machine to a repair place for fear that if it is a simple repair they will not be honest. Can anyone give me advice on whether this is a problem that requires a new motor or major repair? Thank you!
Although it's never to be recommended, it is sometimes possible to vacuum up a little water without doing significant damage. However, the fact that your machine then stopped suggests that the electrics got wet. That may or may not have caused expens ... Vacuums
I have an endurotronic 4111 electrolux vacuum called ''the boss'' and the cable wont retract into the vacuum when i depress the button on the top. how do i dismantle parts to have a look to see if it will repair or not. does anyone have a repair manual for this vacuum. thx
... Electrolux Vacuums
I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac
VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter
There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums
I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum
The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.
... Panasonic MC-V7515 Bagged Upright Vacuum
My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?
Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall
That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums
My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?
Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums
I have an Electrolux Oxygen 3 vacuum I purchased rebuilt. After 1 month the power stopped working. I took it into Electrolux Authorized repair dealer, which was a horrible experience. When we received it back it was clearly not as powerful as before. Does anyone have any suggestions on what the problem may be? I would rather fix it myself than take it back to them. The next repair center is too far away. I am pretty good with fixing things, just needs some guidance. I think the repair center rep
Never have liked Electrolux doing any repair because it has been my experience that they don't do what they say they did....if you can read between the lines.....give me a picture of the unit and more details and I'll try and help you. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.
... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
Repair Service I have a Miele White Pearl. I have a short in the head part of the vacuum ad need repair. Do you know a repair shop near Ely, Minnesota?
Maybe this link will help\015\012http://www.miele.com/locator.asp?nav=7 ... Miele Red Star Bagged Canister Vacuum
No detailed Repair Kit instructions for Edwards E2M5 vacuum pump
Repair belt model#5893 typebvz - Eureka Altima Upright Vacuum Model 2996AVS Vacuum
LiteSpeed Models 5700 and 5800 Series \015\012 \015\012 Eureka\015\012 Style U Belt 2 Pack (54312)http://www.usavacuum.com/Eureka- ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t
... Hoover Vacuums
I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.
My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller [email protected]
A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums
Does not vacuum effectively. It smells like it is burning. I have only had this one year and hardly use it. When I brought it to a local vacuum repair place, he wanted to sell me another one, and, of course, wanted to trade mine towards another.
Miele vacuums are famous for having hair and carpet fibers getting caught in the roller bearings. That can cause a bad smell. The motors in Mieles are very well built and I have a hard time believing that the suction motor is going bad in 1 year. ... Miele S548 Bagged Canister Vacuum
I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?
There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum
Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015
You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum
Miele vacuum cord repair - Miele Vacuums
Http://www.sannerud.com/house/miele.html ... Miele Vacuums
Does the turbo nozzel come apart to repair? - Electrolux Harmony Canister Vacuum - EL6985 Vacuum
Hi, yes, the turbo nozzle can be broken down with just a little time and effort. The two plastic wheels in the rear pop out, and then you'll see 6 screws on the bottom of the unit. Once these have been removed, gently pry the top and bottom pieces ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum
Vacuum repair - Vacuums
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum