Having problems with your Eureka Sanitaire S3686 Bagged Canister Vacuum ?
It just doesnt power on - Eureka Sanitaire S3686 Bagged Canister Vacuum
It just doesn't power on
Repair Help & Product Troubleshooting for Eureka Sanitaire S3686 Bagged Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
It just doesnt power on - Eureka Sanitaire S3686 Bagged Canister Vacuum
It just doesn't power on ... Eureka Sanitaire S3686 Bagged Canister Vacuum
Overheated vacuum After I finished vacuuming the library last night I changed the bag and shook out both filters and vacuum would not restart. The canister unit felt real warm to the touch but I had been using it a least 1/2 hour non stop. The bag was pretty full but not overly so. It's a Simplicity canister with power head. The carpet is long shag from the 70's Did it just over heat? Thanks Shauna
It normally won't over heat unless the bag is too full, the filters are clogged, or you have have a clog in the hose or down by the brush roll, the inlet may be clogged. Some will restart after a while, some others have a reset to push. If it won't ... Simplicity 7850 Premier Bagged Canister Vacuum
I have an old Miele canister vacuum and I do not know how to disassemble the hose to check for a clog. I think it sucked up a nerf ball the size of a ping pong ball. I changed the bag but it did isn't appear to be in the bag. The vacuum powers on but I do not have suction with the hose, and since the hose has hard plastic elbow joints I do not want to pry them apart and break it
Hi Emily: If you have the model number for your machine you may be able to find your manual on the Miele website. Check ... Miele Vacuums
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
I have the top of the line kenmore canister vacuum. According to the bottom plate the model nimbler is 116.28015700 I was doing the normal vacuuming and the bag full light came on and the vacuum action stropped. There is still power to the mortorized handle and agitator attachment. Is there some type of circuit breaker reset button for the vacuum function? This unit is probably less that two years old and has had very little use
... Kenmore Vacuums
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums
Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v
Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums
No suction power on my eureka boss vacuum (vacuum bag has been changed)?
Most probably a clog in the neck. This is where the power head connects to the body of the machine. Remove the base plate (screws in). Take a look at the back of the head behind the beater bar. There is likely something blocked in the nec ... Eureka Boss 7601 Bagged Upright Vacuum
Power head gets no power - Kenmore 23313 Whispertone Bagged Canister Vacuum
... Kenmore 23313 Whispertone Bagged Canister Vacuum
Eureka mighty mite switch - Eureka Mighty Mite 3670 Bagged Canister Vacuum
... Eureka Mighty Mite 3670 Bagged Canister Vacuum
Where is reset button on EL7020A power head - Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
Eureka 4870 will not power on - Eureka Smartvac 4870 Bagged Upright Vacuum
It is probably a thermal issue ... Eureka Smartvac 4870 Bagged Upright Vacuum
My vacuum does not suction floor debri the canister says change bag, i changed it 2 times with recommended electrolux bags. It will suctionwith wand and brush but not with power head
\015\012The power head has a separate motor to drive powerful carpet cleaning.Check if that motor is getting blocked or if its running slow/weak.Also check from any blockage in vacuum line.\015\012Keep updated with the results.\015\012Than ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
Canister has no power - Samsung Ultra Quiet 9073R Bagged Canister Vacuum
... Samsung Ultra Quiet 9073R Bagged Canister Vacuum
Hoover S3590 Bagged Canister Vacuum power issue
The problem you are describing sounds like to be electrical in the cord reel. I would take it to a repair shop for estimate, sometimes these can be repaired rather than replaced. If under warranty, I would definitely take it in. ... Hoover S3590 Bagged Canister Vacuum
I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope
Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums
I have an old (50s) GE vacuum canister model VIIVTI made in Bridgeport, and I don't know what kind of bag it uses. It looks like a Eureka, but it's definitely GE.
... GE Vacuums
No power - Numatic Henry Bagged Canister Vacuum
The most common cause of this problem would be breakage of the wires in the power cord at the point of entry to the vacuum cleaner body. With the power connected you may be able to prove this by flexing the cord at this point, particularly by pushin ... Numatic Henry Bagged Canister Vacuum
Hi I was wondering if you could tell me the 'mother'company who makes Fantom vacuums? We are looking at the Fantom Power Pet bagged canister 12 amps. do you have any feedback or helpful information on this unit? thanks Leslie
Hi Leslie, \012\012The mother company is Euro-Pro or Shark. \012\012My feeling from a service aspect, they are pretty cheap units, and when it comes time for a service, they are a little expensive to fix. You would be better o ... Fantom Vacums FC251 Canister Vacuum
Power nozzle shuts on and off - Kenmore 22612 Bagged Canister Vacuum
(2 years later) in my case the problem was in the "wand". There is a 'female' (not sexist - this is what it is called) plug on the outlet side of the "wand" (handle). The "tube' that attaches between the handle and the "power head" (the thing that h ... Kenmore 22612 Bagged Canister Vacuum
No power to my miele s558? - Miele S558 Red Velvet Bagged Canister Vacuum
It's a bad model that's why they took it off the market. Mine is doing the same thing have taken it in twice for the same reason. First time they replaced the cord $200.00 which I did not believe it was the problem. A year and a half later still c ... Miele S558 Red Velvet Bagged Canister Vacuum
How to open 116.23512301 vacuum canister AC section to wire in replacement 4370608 cable assy. This assembly contains the receptacle that powers the hose. I found the two screws below the bag cover, but can't figure out how to release the end near the retractor lever.
... Kenmore Vacuums
MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.
You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums
ON Off Power switch failed bissell 6900 - Bissell 6900 DigiPro Bagged Canister Vacuum
See this solution:http://www.fixya.com/support/t371681-bissell_6900_stopped_working_open_thing ... Bissell 6900 DigiPro Bagged Canister Vacuum
Powerhead doesnt work at all - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
Push the red reset button on top. ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum